- 06 Jul, 2021 7 commits
-
-
Federico Vaga authored
Signed-off-by:Federico Vaga <federico.vaga@cern.ch>
-
Federico Vaga authored
In some SVEC+ADC designs data is swapped in HW, so there is no need to swap them again in software Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by:
-
- 05 Jul, 2021 19 commits
-
-
Federico Vaga authored
5.0.3 - 2021-07-05 ================== Added: ----- - bld: CI support Fixed ----- - doc: add offset units - sw: calibration value at boot time incorrect - sw: use YAML for fau-calibration
-
Federico Vaga authored
-
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
5.0.3 - 2021-07-05 ================== Added: ----- - bld: CI support Fixed ----- - doc: add offset units - sw: calibration value at boot time incorrect - sw: use YAML for fau-calibration
-
Federico Vaga authored
-
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
It may help other programs to process this output Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by:
-
- 02 Jul, 2021 12 commits
-
-
Federico Vaga authored
The calibration and the default range were not set consistently. The calibration initialization was running before when the default range was the result of a memset (0 -> 10V). The code that initialize the voltage range to 1V happens after but without applying again the calibration values. To solve the problem, now the function that sets the voltage range also sets the calibration values. Ding this allowed to reduce the code in the voltage range assignment in the ZIO part. Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
-
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
Use containers, and more building tests. Remove the koji and RPM part (we will work on that again in the future but now it does not work anymore) Signed-off-by: -
Federico Vaga authored
5.0.2 - 2021-07-03 ================== Fixed ----- - sw: calibration value for ADC were not applied correctly
-
Federico Vaga authored
-
Federico Vaga authored
Signed-off-by: -
Federico Vaga authored
The ADC calibration was applying DAC values Signed-off-by:
-
- 11 Jun, 2021 2 commits
-
-
Federico Vaga authored
5.0.0 - 2021-06-11 ================== Fixed ----- - sw: concurrent DMA transfers are possible thanks to a wait and retry algorithm - sw: wait 400ms before reading the temperature the first time (the hardware takes time to setup the thermometers) - doc: use cheby files from hdl instead of special implementations
-
Federico Vaga authored
-
