Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Reduce the possible range in Kconfig to the half of the possible range.
E.g. setting job to be run every 40minutes is not trivial and */40 will
not work. Instead it will run the job at minute 0, then 40, then again
at 0 (after 40min, then after 20min).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

And fix two typos in the script itself
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Before the fix in some rare cases, radiusvlan could report a receive
of frames from another interface. This could lead to a wrong
authentication of a device connected to a port.

The problem is caused by a behaviour that if a socket is created it
listens on all interfaces until the bind function is called. It might
happen that later calls of recvfrom function will handle frames
received from other interfaces. To prevent that, radiusvlan flushes
all frames received before socket is bound to an interface.
The lost of frames is meaningless since all frames that radiusvlan
listens for are sent periodically.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Print exact command which is or would be run to change VLAN
configuration.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

In dry run mode no changes to the VLAN configuration are applied.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Remove superfluous spaces when generating Kconfig_port_timing.in by gen_kconfig_port_timing.sh
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

fix script generating Kconfig_port_timing.in to include change from
commit:
Kconfig: allow configuration of externalPortConfigurationEnabled in all timing modes
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Disabling of SFP's TX is possible only via HAL.
Disabling it I2C directly is a risky, it can corrupt SFP's EEPROM if
HAL is running.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

The SDBfs library has been re-licensed as LGPL v2.1 in order to allow it
to be linked to proprietary software.

The permission to re-license those files has been approved by CERN in
2018 and then in 2021 (and also by its main author).

Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>

Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>

After reset of the CPU (ARM) GPIO pins are set as input. During
configuration they were set to 0, which had a meaning to the i2c
transfer if the last transfer before reset was not completed (e.g. by
the switch restart).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

The I2C transfer can be interrupted by a restart of a switch. An I2C slave
is not aware about an ARM restart so it expect the continuation of the
transfer.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

To reduce the CPU load the data from one SFP is read every 300ms. In the
worst case all monitoring data is updated every 5.4s.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

This commit reduces the size of periodic read for each SFP from 256B to 16B.
Since the I2C transfer are bit-banged, this commit reduces CPU
utilization if monitoring of SFPs is used (CONFIG_READ_SFP_DIAG_ENABLE).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

To be reported by SNMP as SNMPv2-MIB::sysContact.0 and SNMPv2-MIB::sysLocation.0
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

This commit requires uplift of ppsi
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

This version already includes
lldpd support sending LLDP frames over VLAN
and other patches since 1.0.5
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Before it was printed as signed
Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>

Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>

May be useful to find offsets of structures that are not printed.
Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>

Fixes after ppsi update for WRPC. Should not affect WRS
Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>

Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>

Signed-off-by: Adam Wujek <adam.wujek@creotech.pl>