Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Update callers of wrs_shm_get_and_check to recognize return value
WRS_SHM_INCONSISTENT_DATA. Update to use defined values instead of numbers.

Update:
--snmpd
--tools/rtu_stat
--tools/wr_mon
--tools/wr_phytool
--tools/wrs_sfp_dump
--tools/wrs_vlans
--wrs_watchdog
--wrsw_rtud

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Check the consistency of shmem during opening with wrs_shm_get_and_check.
It was possible that sequence number was increased during the opening, but it
was interpreted as version error.

Add defines describing different return errors.

This change is backward compatible.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Keep explicitly lock bit in the sequence variable as a LSB bit.
This solution is backward compatible. The difference is only when shmem is
lock twice. Before it was treated as unlocked, now still as a lock.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Print error message when shmem is locked or unlocked multiple times.
To be precise it will print error only on even locks or unlocks.

Move the increment of sequence before checking the flags to simplify further
if-conditions.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Remove excessive locks from the function delete_htab_entry.
Function rtu_fd_commit is always guarded with shmem lock. The function
rtu_fd_commit calls rtu_hw_commit, which calls delete_htab_entry. By this
function wrs_shm_write with a parameter WRS_SHM_WRITE_BEGIN was called twice
before it was called twice with a parameter WRS_SHM_WRITE_END.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Lock HAL's shmem on write to let a reader know about potential inconsistent
data

List below indicates which functions requires a lock (marked as "UPDATE").
minipc:
--halexp_lock_cmd:
  --hal_port_enable_tracking - not
  --hal_port_start_lock - UPDATE
  --hal_port_check_lock - not
--halexp_pps_cmd
  --rts_adjust_phase - not
  --shw_pps_gen_adjust - not
  --shw_pps_gen_busy - not
  --hal_port_pshifter_busy - not
  --shw_pps_gen_enable_output - not

hal_port_update_all:
--poll_rts_state - not
--hal_port_poll_sfp:
  --shw_sfp_module_scan - not
  --hal_port_insert_sfp - UPDATE
  --hal_port_remove_sfp - UPDATE
--hal_port_fsm - UPDATE

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

By default, on the startup the VLAN with VID0 is created with the mask
0xffffffff. It is used to pass all the traffic between ports. However, when
VLANs configuration is read from the dot-config now it also remove this VLAN.
We cannot relay on how the system was configured before.
If such configuration is needed it can be configured in the
CONFIG_VLANS_VLAN0000 config option.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

We cannot relay on the previous configuration. So clear, then apply new.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

--Change parameter --pumask to --puntag; "mask" part is misleading, since full
  mask is not supported.
--use "pmode" rather "pmode"
--improve help message
--support -1 for pprio to disable fix priority
--support -1 for rprio to disable fix priority
--change VLANS_PORTXX_UMASK_ALL and VLANS_PORTXX_UMASK_NONE into
  VLANS_PORTXX_UNTAG_ALL and VLANS_PORTXX_UNTAG_NONE

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

--Add new SNMP objects indicating the status of scripts run at boot
  --wrsAuxClkSetStatus
  --wrsThrottlingSetStatus
  --wrsVlansSetStatus
--Update wrsBootSuccessful to take into account status of objects above
--Update corresponding scripts to save status information at the execution:
  --etc/init.d/vlan.sh
  --etc/init.d/wrs_auxclk.sh
  --etc/init.d/wrs_throttling.sh
--Update MIB
--Update wrs-user-manual
--Update wrs_failures

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Add to Kconfig:
--RTU_HP_MASK_ENABLE
--RTU_HP_MASK_VAL

Update wrs_vlans:
--add parameter --hpmask
--read RTU_HP_MASK_* from dot-config
--print hpmask with plist

add a new minipc call rtud_export_hp_mask for HP mask

Update wrs-user-manual
Update wrs-developer-manual
Update webinterface

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

remove --debug flag
support -v/-q flags for more/less verbose output

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

It was not possible to pass parameters when vid 0 was the first one specified
wrs1#wrs_vlans --rvid 0 --rdrop 1 --rvid 1 --rdrop 1
wrs_vlans: missing "--rvid <vid>" before rtu cmd
However, it was possible if any other vid was specified before:
wrs1#wrs_vlans --rvid 1 --rdrop 1 --rvid 0 --rdrop 1

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Update vlan.sh init script to let wrs_vlans to read configuration from
the dot-config.

Remove vlan_config.sh since it is not used anymore.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Changes:
--add "--file|-f" parameter to read VLAN configuration from dot-config
--"--debug" can take parameter
--print VLAN configuration to be applied if debug enabled

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Specify vlans for ppsi in dot-config's field PORTXX_PARAMS.
Use ppsi_vlans for that, with a colon separated list.
PORTXX_PARAMS="...,ppsi_vlans=1:2:9"

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Keep all VLAN related configuration in the Kconfig_vlans.in.
Source this file in the Kconfig
Also copy it to the target.
Kconfig_vlans.in is generated by a command:
userspace/host_tools/gen_vlan_kconf.sh > Kconfig_vlans.in

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Since the Kconfig for VLANs contains repetable options, it is more convenient
to generate it automatically, than write it by hand.
To use this tool, simply redirect the output to the file

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

rtu deals with frames not packets. Fix printouts.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Add a support of sourcing another file in Kconfig

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

PHP code of the web interface was updating values of "upload_max_filesize"
and "post_max_size" in the /etc/php.ini. Besides it is extremely bad idea to
do that, such changes to take place require restart of lighttpd, which was
never performed. Luckily after the update of /etc/php.ini it was also copied
to flash at the location /usr/etc/php.ini. Because of this update via
webinterface worked only when:
--firmware.php was opened via web browser
--restart of a switch was performed

The fix contains a patch to set these values in the php.ini and remove
the update of php.ini by php code.

Set maximum upload limit size to 30M in php.ini.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Following changes were made in this commit:
--Add quotas to the arrays in the file var/www/data/wrs-data.php
--Change CONFIG_PORT00_PARAMS to CONFIG_PORT01_PARAMS in the
  var/www/endpointcalibration.php. It looks like it was missed during
  interface renaming.
--Change "file" into "firmware" in the firmware input form
--Remove the help when mouse hovers over the form. The help wasn't filled
  anyway (remove title="'.$row["help"].).
--fix part of the shell_exec command: awk '{print $NF}'
  escape the $
--use index 0..5 in the sfpcalibration.php
--remove unlink after calling "rename" function

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Implement [Feature: 1363] support of a custom script to be run at boot

Add the following objects to wrsBootStatusGroup:
--wrsCustomBootScriptSource
--wrsCustomBootScriptSourceUrl
--wrsCustomBootScriptStatus
Update wrsOSStatusGroup.wrsBootSuccessful to use information from the above
objects.

Update wrs_failures

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

This will allow users to have special configuration (that is not possible to
achieve by just using dot-config) without a need to manually handle custom
script.

The script can be used from /wr/bin/custom_boot_script.sh or downloaded during
the boot. It is not possible to execute a script which was downloaded during
the previous boot. But a script can be written in such way to copy itself to
/wr/bin/custom_boot_script.sh.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Add a minipc calls added at commits:
[Feature: 1055] userspace/tools: add unrec command to rtu_stat
[Feature: 1055] userspace/tools: add learning command to rtu_stat

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

no technical change

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Use default hostname "wrs" when CONFIG_HOSTNAME_STATIC = y, but
CONFIG_HOSTNAME_STRING is not defined.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Length should be 128, not 64.
Bug introduced by:
a51052af

 userspace/snmpd: remove protocol from wrsConfigSource object

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Improve documentation of throttling's settings in the dot-config.
In the wrs-user-manual and in the Kconfig.

Supplements:
Merge branch 'greg-throttling'

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Allow to specify hostname in the dot-config URL and in PPSI URL.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Before, some were without @t{}, some used @i{}.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

It is much more readable to have "port X" than "further port" in
the Kconfig.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

--add struct shw_sfp_header sfp_header_raw to the struct hal_port_calibration.
--Increase HAL_SHMEM_VERSION to 9 due to the above
--add a parameter to the wrs_sfp_dump to dump eeprom directly from the SFP or
saved data from HAL

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

stop explicitly snmpd before reboot to avoid messages:
Jan  1 00:54:23 snmpd[1290]: read_config_store open failure on /var/lib/snmp/snmpd.conf
Otherwise snmpd was stopped after unmount of filesystems.

Stop monit to avoid possible respawn of processes during shutting down.

remove "null" from the line in /etc/inittab
null::shutdown:/etc/init.d/rcK
to get printouts to the console.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>