Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

There is a tool wrs_status_led to set status LED, so use it (at boot time).

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Compiled from commit 1b32dbb5 of wrpc-sw repository.

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Check if head is not NULL

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

So far only to control offset between PPS-in and PPS-out in GM mode

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

1. Add new paramter CONFIG_EXT_PPS_LATENCY_PS in dot-config.
   Calibration is needed to align the PPS out to PPS input in GM mode.
2. Add new variable ext_pps_latency_ps in struct spll_stats, using it
   to transfer the ext_pps_latency parameter to WRPC-SW.
3. Change SPLL_STATS_VER to 4, modify the related function.
4. (deleted from the commit)
   Add a new tool function: wrs_ext_pps_latency, which will change
   the Main PLL phase shift in GM mode, according to the parameter
   CONFIG_EXT_PPS_LATENCY_PS in dot-config. Add this new function to
   startup-mb.sh, making it autostart.

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

update wrsfl_release_defconfig
(Removed from the original commit) update tx_phase_cal.conf

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

A kernel module file asix.ko and a tool ioctl will be generated.
After insmod the asix.ko, a new network interface, eth1, will be found.

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

HA and WR profiles use the same value.

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Add values that are displayed in wr_mon for servo.

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Some OIDs are not used if l1sync is used, then don't return them since
a value e.g. 0 can have a valid meaning.

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Return the same values as in wr_mon. Please remember that this value is
still an ESTIMATION!

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>

Signed-off-by: Adam Wujek <dev_public@wujek.eu>