Kconfig

endchoice
config CUSTOM_BOOT_SCRIPT_SOURCE_REMOTE_URL
	string "URL of a custom script"
	depends on CUSTOM_BOOT_SCRIPT_SOURCE_REMOTE
	help
	  URL to the custom script. HOSTNAME, IPADDR and MACADDR are
	  substituted before retrieving the file.

	  Example:  "tftp://morgana/custom-script-IPADDR"

endmenu

menu "LLDP options"
config LLDPD_DISABLE
	bool "Disable LLDP daemon"
	default n
	help
	  Disable LLDP daemon to prevent sending LLDP frames. It may be useful
	  for networks not using LLDP or with a low latency requirement.

config LLDPD_TX_INTERVAL
	int "LLDP TX interval"
	default 5
	depends on !LLDPD_DISABLE
	help
	  Define how often LLDP frames are sent.

config LLDPD_MANAGEMENT_PORT_DISABLE
	bool "Disable LLDP on the management port"
	default n
	depends on !LLDPD_DISABLE
	help
	  Disable LLDP traffic on management port.

config LLDPD_MINIMUM_FRAME_SIZE
	bool "Send only minimum information via LLDP"
	default n
	depends on !LLDPD_DISABLE
	help
	  Send only minimum information via LLDP. May be useful in networks
	  which require low latency.
endmenu

config HTTPD_DISABLE
	bool "Disable web interface"
	default n
	help
	  Disable web interface.

menu "Developer options"
config MONIT_DISABLE
	bool "Disable monit"
	default n
	help
	  Disable monit to prevent processes' restarts. It may be useful for
	  development.

menu "Fan speed control"
config FAN_HYSTERESIS
	bool "Use hysteresis to control fan speed"
	default n
	help
	  Use hysteresis to control fans. Enable fans with PWM value
	  CONFIG_FAN_HYSTERESIS_PWM_VAL} when PLL's temperature exceeds
	  CONFIG_FAN_HYSTERESIS_T_ENABLE. Disable fans when temperature drops
	  below CONFIG_FAN_HYSTERESIS_T_DISABLE. These options are intended to
	  be used during development to reduce noise generated by a switch.
	  Don't use in production as this may affect the synchronization
	  performance.

config FAN_HYSTERESIS_T_DISABLE
	int "Disable fans temperature"
	default 60
	range 0 80
	depends on FAN_HYSTERESIS
	help
	  Temperature at which fans are disabled when working in hysteresis mode.

config FAN_HYSTERESIS_T_ENABLE
	int "Enable fans temperature"
	default 65
	range 0 80
	depends on FAN_HYSTERESIS
	help
	  Temperature at which fans are enabled when working in hysteresis mode.
	  Maximum allowed value is 80

config FAN_HYSTERESIS_PWM_VAL
	int "Value of fans' PWM"
	default 100
	range 4 1000
	depends on FAN_HYSTERESIS
	help
	  PWM value used to drive fans. Range from 4 to 1000.

endmenu # "Fan speed control"

config READ_SFP_DIAG_ENABLE
	bool "Read SFPs Diagnostic Monitoring"
	default n
	help
	  Let HAL to read Diagnostic Monitoring from SFP's eeprom.

choice
	prompt "Compilation optimization"
    
    config OPTIMIZATION_SPEED
        boolean "Execution time (-O2)"
        help
           GCC performs nearly all supported optimizations that do not involve a space-speed tradeoff.
           
     config OPTIMIZATION_SIZE_SPEED
        boolean "Size and execution time (-Os)"
        help
           Optimize for size. Enables all -O2 optimizations except those that often increase code size.
           
     config OPTIMIZATION_DEBUGGING
        boolean "Debugging (-Og)"
        help
           Should be the optimization level of choice for the standard edit-compile-debug cycle

     config OPTIMIZATION_NONE_DEBUGGING
        boolean "Debugging without optimization(-ggdb)"
        help
           Compile without optimization and with debug informations 
endchoice

config OPTIMIZATION
	string
	default "-Os -ggdb" if OPTIMIZATION_SIZE_SPEED
	default "-O2 -ggdb" if OPTIMIZATION_SPEED
	default "-Og -ggdb" if OPTIMIZATION_DEBUGGING
	default "-ggdb" if OPTIMIZATION_NONE_DEBUGGING
	default "-ggdb"

endmenu # "Developer options"

menu "RTU HP mask"

config RTU_HP_MASK_ENABLE
	bool "Set custom High Priority mask in RTU"
	default n
	help
	  Set the mask which priorities are considered High Priority (this
	  only concerns the traffic which is fast-forwarded).


config RTU_HP_MASK_VAL
	string "HP mask"
	default 0
	depends on RTU_HP_MASK_ENABLE
	help
	  Mask with priorities (eg. 0x9 => priority 4 and 0 are considered HP)


endmenu

source Kconfig_vlans.in