This new parameter is used to control the configurable parameter
L1SyncOptParamsPortDS.timestampsCorrectedTx when
L1SyncBasicPortDS.optParamsEnabled is set to true.

The delayCoefficient can be set in ppsi.conf file either with the
delayCoefficient (double) parameter or the scaledDelayCoefficient
(RelativeDifference)  parameter. In ppsi, the priority is given to the
scaledDelayCoefficient.

When the extension L1SYNC is not available (no data), the value of
L1SyncEnable and L1SyncState are emulated and displayed. Some VERYX
tests need these information also when L1SYNC is disabled.

Due to changes in the standard (Clause 17.6.5), the slaveOnly parameter
must be forced to FALSE when externalPortConfiguration is enabled.

- When optParamsEnabled is set, the TLV send need to be extended with
extra values. Fix here the length of the TLV and the whole message.
- Fix print issue of the signaling TLV

- Add DelayAsymmetty calculation for HA
- Avoid using pow() math function call. Use directly a constant value.
Done for HA and WR.

- The ntohx() is now used to unpack messages and htohx() to pack them.
Most of the time only htohx() was used for paking and unpacking
messages.
- Code optimization

On little indian architecture, the calculation of the correction field
was wrong in the PDelay_Resp_FollowUp message. This was introducing a
big random offset (few us) of the PPS.

Fix warning introduced in the commit:
Implement one-step clock for HA & WR profiles
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

- Many information were store in a common static structure (to_config).
However depending on the PPSI instance configuration these information
need to be stored per instance. Mainly it concerns the rand value
(which_rand and the counter reset value). Only the timer name stay now
in a common arrea.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

    According to the clause 9.3.2.3, the qualification is now not
evaluated for the ErBest foreign master.
    On ANN_RECEIPT timout, the ErBest is removed from the list of
foreign master to avoid to jump immediately to SLAVE state

    - Add new config parameters (l1SyncRxCoherencyIsRequired,...)
    - Add new profile: CUSTOM. It will be mostly used for testing
    - Fix issue on state name: "pre_master" instead of "pre-master"

- Add new config parameters (l1SyncRxCoherencyIsRequired,...)
- Add new profile: CUSTOM. It will be mostly used for testing
- Fix issue on state name: "pre_master" instead of "pre-master"

According to the clause 9.3.2.3, the quualification is now not evaluated
for the ErBest foreign master.

The one-step clock didn't work for HA & WR profiles. This new
implementation is based on a new hook "handle_sync" called in case of
one-step clock mode.

- Fix issues introduced in last commit "Timeout management correction"
- Code optimization
- Protect FAULT timeout in case of timeout overload. It can append
because the logMinDelayResponse can be changed on real-time by the
received DELAY_RESP message

In the ptp servo the adjustment of the time was too slow. When the
difference of the time with the master was less than 1 second, the
adjustment was done only with the frequency. In case if the difference
is 0.999s, it can take a very long time to adjust the time.
Changes made :
- Adjust with frequency only when time difference is below 20ms
- Check the timestamp validity before each calculation
- Create a new function to check the timestamps and use it on all
servos. This improve significantly the size of the code.
- Add verification in order not to set an invalid UNIX time

Change the default value of "alarmDetected" to force execution of fsm
the first time.

When received frames are displayed (diagnostic mode), PPSI was staying
forever in a loop due to unexpected TLV received in the frame.

This was due to the introduction of system timers in the main loop of
the switch. In minirpc the pool() system call exited sometime when the
timer fired. Some other problems have been found during the debugging
process. Some of them have been already adressed :
- In minirpc, loop on pool() system call if the call is interrupted.
- Wrong check in function wrs_locking_poll(). Was working by chance.
- L12_state_machine() was calling to many often the state handle. It was
increasing the number of hardware calls for nothing.

TODO: The returned values for the function wrs_locking_poll(), halexp_lock_cmd(), and hal_port_check_lock() should be reviewed to be more consistent.

based on jcb's commit from wrs
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

- This function checks now the minimum and maximum values which can be
encoded into a RelativeDifference type.
- Bux fix for the calculation of min/max value conversion (special
cases)

- The origin timestamp sent in SYNC and DELAY_REQ messages is corrected
with the egressTimestampLatency.

- The timeout expressed in ms is stored in an integer value. A Log
interval may have a value in the range -128,127. The timeout cannot
covers all this range. A protection as been added to avoid wrong timeout
calculation which might generate a crash of PPSI.
- A new function is also added pp_timeout_log_to_ms() to verify the log
Interval and calculate the timeout.
- Optimize the execution of pp_timeout_set()

- We do not wait the L1SYNC state UP before to go from UNCALIBRATED to
SLAVE state.
- When the link goes down, we force the next state to DISABLE

- Set the minimum and maximum values of some parameters
- Fix format issues in pp_printf and sscanf

- Force to stay on UNCALIBRATED state (was going to slave state)
- Force to stay on PRE-MASTER state  (was going to master state)

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

- Reset local remaining time-out when 'select' exits due to a signal

- Change calculation of delayAsymmetry
- Set offsetFromMaster (generic servo)
- Set meanDelay (generic servo)

- The %f format is not supported in pp_printf. So we will not display
the float value in error messages.
- Change DBL_MIN by -DBL_MAX to have the minimum value of a double

- Optimize the scheduler (main_loop) using system timer. It makes the
calculation of the timeout more precise  taking into account execution
time of some part of the code

- Optimize the L1SYNC sent messages too take into account the time spent
to send an frame

- Move initialization of configurable parameters in L1SYNC init hook
- Set the L1SYNC state to DISABLE in the startup otherwise the state is
not set if the port is not connected
- Remove time printing in diag messages
- restrict call to servo only when the state is UP
- Adjust properly the delay returned by each l1sync state functions
- Set REQUEST timeout value dependent of the delay mechanism (E2E/P2P)
- Bug fix: PP_P2P_MECH used instead of P2P
- Optimize the REQUEST timeout to generate asap a DelayReq message after
the first SYNC message received

The default configuration was not copied in the right place in PPSI
instance.