- 20 May, 2020 11 commits
-
-
Maciej Lipinski authored
-
Maciej Lipinski authored
-
Maciej Lipinski authored
changed from daemon.info to a new option default_syslog that uses daemon.info as default and additionally parses syslog messages for info about facility,priority and uses this info if available.
-
Maciej Lipinski authored
Some deamons/etc that log messages to syslog do not specify facility.level in their messages. The logger is configured to parse the message looking for facility.level (option: --prio-prefix). If the message does not include If no facility.priority is specified, the logger will use the one specified after -p, this is now provided. For example, PPSi does not specify facility.priority in messages (hopefully, this will change), without "-p daemon.info", it was reported as user.info. If user wishes to, he/she can override. This is the default config
-
Maciej Lipinski authored
-
Maciej Lipinski authored
-
Ragnar Sundblad authored
Signed-off-by: Maciej Lipinski <maciej.lipinski@cern.ch>
-
Maciej Lipinski authored
-
Jean-Claude BAU authored
-
Maciej Lipinski authored
- behavior for different VLAN modes was incorrect (in table and text) - updates per changes in v6.0 were needed.
-
Maciej Lipinski authored
-
- 19 May, 2020 2 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
- 18 May, 2020 2 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
- 08 May, 2020 3 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
- 07 May, 2020 1 commit
-
-
Tomasz Wlostowski authored
-
- 24 Apr, 2020 1 commit
-
-
Jean-Claude BAU authored
-
- 15 Apr, 2020 1 commit
-
-
Jean-Claude BAU authored
-
- 09 Apr, 2020 2 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
This reverts commit 9c8412e3. S59leap_seconds_file_update is already there to call the script at boot time.
-
- 08 Apr, 2020 6 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
Fixes ifconfig down issue for LPDC ports.
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
Load values from tx_phase_cal.conf file only if MD5 matches. Otherwise, generate new values.
-
Grzegorz Daniluk authored
-
- 02 Apr, 2020 2 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
- 31 Mar, 2020 4 commits
-
-
Maciej Lipinski authored
-
Maciej Lipinski authored
-
Maciej Lipinski authored
So far, only LDPC tx calibration was indicated by blinking link led, now the same behavior was added when LPDC rx calibration is ongoing.
-
Maciej Lipinski authored
Make sure that the status LED does go green before the LPDC tx calibration is finished.
-
- 30 Mar, 2020 2 commits
-
-
Maciej Lipinski authored
Setting the options to force dot-config/IP over DHCP can be dangerous. Until now, the switch would wait endlessly in an infinite loop. This commit introduces a way to escape the loop. This can be done by connecting to the back UART and pressing any key.
-
Grzegorz Daniluk authored
-
- 27 Mar, 2020 3 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
Now it represents the overall status of system clock: - verification with NTP time - leap seconds file
-
Jean-Claude BAU authored
-