HAL didn't read "fiber=" parameter of port from the dot-config

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

When running make menuconfig from /wr/etc, mconf was crashing when dialog box
in the style of radiolist was displayed and special keys (like arrow keys)
were pressed. Crash was due to assetion in function toupper from uClibc.
Function to upper should return unchanged value if passed parameter is not
alpha. However, uClibc's implementation behaves in the different way,
it asserts.
After assert following message was printed:
(./mconf: libc/misc/ctype/ctype.c: 320: toupper:
Assertion `((((unsigned int)((c) - 0)) <= ((127 * 2 + 1) - 0)) ||
((c) == (-1)))' failed.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Print information about performed dot-config check and source of dot-config.
Information about potential problems in dot-config can be easily lost among
all printouts during the boot.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Maciej Lipinski authored 9 years ago and Adam Wujek committed 9 years ago

this feature is useful for Btrain guys who want to see whether their frames are
sent and delivered where needed

Create script which can be filled with vlans' configuration

So far there are no VLANs configured in this script, but it is good start.
When one needs can populate this sctipt on his/her own.
NOTE: VLANs should be configured before any other traffic is allowed. This
is done by previous commits.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Switching is enabled when interfaces are up. Bringing up interfaces is delayed
to be able to configure VLANs first.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Delay bring up of wr interfaces to be able to configure VLANs first.
Otherwise some network traffic can be passed befre VLANs are configured corectly.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Retry connecting to the RTUd mini-rpc server.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Set-up VLAN related registers during driver load instead of during opening
(bringing up) interfaces.
From now VLANs can be configured after loading the driver, but before bringing
up of interfaces. By this no switching is done without VLANs beeing configured.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

compile and copy needed mconf used by make menuconfig

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Support assembling dot-config's URL from DHCP options:
--the filename
--the BOOTP next server option
In this case TFTP protocol is used. It is similar to the pxe booting.

Also update documentation.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Don't run DHCP's default script (/usr/share/udhcpc/default.script) when getting
URL to the dot-config via DHCP. When the script was run, then the IP address
was set but not the default routes. Now just get URL via DHCP, setting IP is
done by running script /etc/init.d/network from /etc/init.d/dot-config or from
rcS.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

There was a wrong OID set in show-pstats script

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

SNMPd bugfixes

t_n_rows (n_rows before) has to be local for table. Having it global sometimes
caused to print wrong number of rows in tables. This bug may even cause snmpd
to crash.
It was dependent on the call order of *_data_fill funtions.

Change the n_rows into t_n_rows, since the usage of n_rows variable is common
in the snmp code. By this avoid potential errors like variable overleaping
problems.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Get the worst value not the last.
Move copying of data into prev outside loops.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

When wrsPTPStatus can only be updated when both ptp_data and spllStatus are
updated. Otherwise spllStatus changes may cause wrong delta calculation
in get_wrsPTPStatus function. In this case prev data is the same as current,
which may produce false error.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

There was a bug in wrsTimingStatus_data_fill that even if not all of the
wrsPtpDataTable_data_fill, wrsSpllStatus_data_fill or
wrsPortStatusTable_data_fill were updated all objects in the
wrsTimingStatusGroup were updated. As a side effect it may happen that all
prev_ values were compared with exactly the same set of data (since there was
no update in particular data). By this delta were zero and wrong value was set.

The bug may be hit when snmp requests rate is lower than snmpd's cache timeout.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Before at the beginnig of the hwinfo script, hwinfo_error was written to the status file.
Then if there was success or warning then update was written to status file.
Snmpd could read error even there was no error.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Try again when read error from file

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Up eth0 before trying to get URL to dot-config via DHCP (needed when switch
start without IP address)

fix missing "CONFIG_" in CONFIG_DOTCONF_SOURCE_LOCAL

run /usr/share/udhcpc/default.script when getting URL to dot-config to get
IP address to avoid another DHCP requests just to get IP.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

By this avoid log entires during normal startup:
snmpd[1138]: wrsPortStatusTable_data_fill: Unable to read PPSI's shmem

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

add:
--CONFIG_ROOT_PWD_CLEAR
--CONFIG_PTP_REMOTE_CONF

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Add commit:
increase Announce rcv timeout to 20 - workaround for the WRS

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Support getting URL to dot-config via DHCP

Add support of different dot-config sources.
Improve some help information.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Only for the case when dot-config source changed during run-time.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

force-dhcp can be used to retrieve a URL to the dot-config, which is downloaded
during boot.
try-dhcp the same as above but don't complain about unsuccessful receive of the
URL via DHCP to SNMP.

Update:
--MIB - add tryDhcp and forceDhcp to the wrsConfigSource object; add
        dhcpError to the wrsBootConfigStatus object
--SNMPd - same as the above; don't error in wrsBootConfigStatus when tryDhcp
          fails
--dot-config's script - support new dot-config sources
--Kconfig - support new dot-config sources
--wrs_failures
--wrs-user-manual
--wrs_release_defconfig - add new items
--create new script for udhcpc to save "filename" configuration field retrieved
  from DHCP server; it contains the URL to the dot-config to be downloaded.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

NOTE: This commit brings non compatible changes into MIB. It should never
happen after release!

Change wrsConfigSource to inform whether dot-config source was local or remote.
Before it contained also information about remote protocol.
Now information from wrsConfigSource, wrsConfigSourceHost and
wrsConfigSourceFilename is stored in wrsConfigSourceUrl.

wrsRestartReasonMonit is moved into place where wrsConfigSourceFilename was
before.

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>