Kconfig

mainmenu "White Rabbit Switch  configuration"

config DOTCONF_FW_VERSION
	string "Firmware version"
	default "8.0-rc1"
	help
	  Free-text information about switch's firmware version. This field is
	  for information purpose only. Additionally this field describes
	  version of Kconfig.

config DOTCONF_HW_VERSION
	string "Hardware version"
	default "3.4"
	help
	  Free-text information about switch's Hardware version. This field is
	  for information purpose only.

config DOTCONF_INFO
	string "Additional info about dot-config"
	help
	  Free-text information about switch's dot-config. This field is
	  for information purpose only.

#
# Select source of dot-config file
# 

choice DOTCONF_SOURCE
	  prompt "Source for a run-time replacement of dot-config"
	  default DOTCONF_SOURCE_TRY_DHCP

config DOTCONF_SOURCE_LOCAL
	bool "Use local dot-config"
	help
	  The White Rabbit Switch is configured at run-time,
	  according to a dot-config .config file. The file
	  is the same .config you are defining now. If you
	  select this option, dot-config is not replaced
	  at run time.

config DOTCONF_SOURCE_REMOTE
	bool "Use remote dot-config"
	help
	  Use the URL to dot-config provided in DOTCONF_URL.

config DOTCONF_SOURCE_FORCE_DHCP
	bool "Force to get the URL to a dot-config via DHCP"
	depends on ETH0_DHCP
	help
	  Retrieve a URL to the dot-config via DHCP at boot.
	  The URL can be configured in the "filename" configuration field of
	  the DHCP server.

config DOTCONF_SOURCE_TRY_DHCP
	bool "Try to get the URL to a dot-config via DHCP"
	help
	  The same as DOTCONF_SOURCE_FORCE_DHCP, but this option does not
	  cause errors in SNMP's objects if the switch fails to retrieve
	  the URL to the dot-config via DHCP.

endchoice

config DOTCONF_URL
	string "URL for a run-time replacement of dot-config"
	depends on DOTCONF_SOURCE_REMOTE
	help
	  tftp://, ftp:// or http:// URLs are allowed. Names are allowed if
	  you configured a DNS server. The special strings HOSTNAME, IPADDR and
	  MACADDR are substituted before retrieving the file.
	  Example:  "tftp://morgana/wrs-config-IPADDR"

config DOTCONF_LOCAL_OVERWRITE
	boolean "Overwrite dot-config with values locally stored in /update"
	default y
	help
	  At boot overwrite dot-config (retrieved from the network or stored
	  locally) with values locally stored in
	  /update/permanent/dot-config/dot-config-overwrite.
	  This functionality can be used to e.g., pre-configure management
	  port after firmware update or to use custom SoftPLL values after
	  firmware update, specific for particular WR switch.

#
# Select source of leap seconds file
# 
choice LEAPSEC_SOURCE
	  prompt "Source for a run-time replacement of leap seconds file"
	  default LEAPSEC_SOURCE_LOCAL

config LEAPSEC_SOURCE_LOCAL
	bool "Use local leap seconds file"
	help
	  A leap seconds file (leap-seconds.list) is already present in the White Rabbit Switch.
	  If you select this option, the leap seconds file is not replaced
	  at run time.

config LEAPSEC_SOURCE_REMOTE_FORCE
	bool "Force remote leap seconds file"
	help
	  Use the URL to leap secondw file provided in LEAPSEC_URL.
	  If the file cannot be downloaded, it will cause errors in SNMP's objects.

config LEAPSEC_SOURCE_REMOTE_TRY
	bool "Try remote leap seconds file"
	help
	  The same as LEAPSEC_SOURCE_REMOTE_FORCE, but this option does not
	  cause errors in SNMP's objects if the switch fails to retrieve
	  the URL to the leap seconds files.
endchoice

config LEAPSEC_URL
	string "URL for a run-time replacement of leap seconds file"
	default "ftp://ftp.boulder.nist.gov/pub/time/leap-seconds.list"
	depends on LEAPSEC_SOURCE_REMOTE_TRY || LEAPSEC_SOURCE_REMOTE_FORCE
	help
	  tftp://, ftp:// or http:// URLs are allowed. Names are allowed if
	  you configured a DNS server. The special strings HOSTNAME, BOOTSERVER, IPADDR and
	  MACADDR are substituted before retrieving the file.
	  Example:  "tftp://BOOTSERVER/leap-seconds.IPADDR"


config PPSI
	bool
	default y

menu "External source of Time of Day at boot"

choice
	prompt "External source of local Time of Day at boot"
	default TOD_SOURCE_NTP
	help
	  Select the external time source of Time of Day at boot.
	  If device gets time from other PTP/WR device the time will be
	  overwritten.

	config TOD_SOURCE_NONE
		bool "None"
		help
		  Don't use external source of local time at startup.
		  It will use date stored at the last reboot or it will stay
		  at the beginning of the epoch (1970).

	config TOD_SOURCE_NTP
		bool "Use NTP"
		help
		  Use NTP as external source of local time at startup.

	config TOD_SOURCE_NMEA
		bool "Enable NMEA Interface to set time in GM"
		help
		  Use NMEA (interface via RS-232) as external source of local
		  time at startup.

	config TOD_SOURCE_IRIGB
		bool "Enable IRIG-B Interface to set time in GM"
		help
		  Use IRIG-B004 (interface via PPS input) as external source of
		  local time at startup.
		  PPS input termination will be enabled when IRIG-B is used.
endchoice

config NTP_SERVER
	string "IP addresses of NTP servers"
	depends on TOD_SOURCE_NTP
	help
	  At boot time, the White Rabbit time can be primed by querying
	  NTP servers, if CONFIG_TOD_SOURCE_NTP is set.
	  Please write here the IPV4 address (e.g.: "192.168.16.1") or
	  the server name to be resolved by an used DNS server.
	  Multiple servers can be defined, please separate them by comma,
	  semicolon or space.
	  An empty string disables NTP-based priming.

choice
	prompt "NMEA Baud Rate"
	depends on TOD_SOURCE_NMEA
	default NMEA_B9600
	help
	  Set baud rate of NMEA interface
	config NMEA_B9600
		bool "9600"
	config NMEA_B19200
		bool "19200"
	config NMEA_B38400
		bool "38400"
	config NMEA_B57600
		bool "57600"
	config NMEA_B115200
		bool "115200"
endchoice

choice
	prompt "NMEA Format"
	depends on TOD_SOURCE_NMEA
	default NMEA_GPZDA
	help
	  Set the NMEA sentence to parse
	config NMEA_GPZDA
		bool "GPZDA"
	config NMEA_GPRMC
		bool "GPRMC"
endchoice

endmenu # "External Time of Day source at boot"


menu "Local Network Configuration"

choice
	prompt "Management port configuration (eth0)"
	default ETH0_DHCP

config ETH0_DHCP
	bool "DHCP forever"
	help
	  Try DHCP on management port (eth0) forever.

config ETH0_DHCP_ONCE
	bool "Try DHCP, if fail use static address"
	help
	  Try DHCP on management port (eth0) for a while, then configure
	  static IP. Useful, when you move switch between various development
	  enviroments.

config ETH0_STATIC
	bool "Static address"
	help
	  Use static address on management port (eth0). Don't try to DHCP.

endchoice

menu "Management port (eth0) Address"
depends on ETH0_DHCP_ONCE || ETH0_STATIC

config ETH0_IP
	string "Static IP address of management port (eth0)"
	default "192.168.1.254"
	help
	  Static IP address of management port (eth0). Please note that
	  wrong IP address will generate a runtime error on the switch.

config ETH0_MASK
	string "Mask of management port (eth0)"
	default "255.255.255.0"
	help
	  Mask of management port (eth0). Please note that wrong mask will
	  generate a runtime error on the switch.

config ETH0_NETWORK
	string "Network of management port (eth0)"
	default "192.168.1.0"
	help
	  Network of management port (eth0). Please note that wrong network
	  will generate a runtime error on the switch.

config ETH0_BROADCAST
	string "Broadcast of management port (eth0)"
	default "192.168.1.255"
	help
	  Broadcast of management port (eth0). Please note that wrong broadcast
	  will generate a runtime error on the switch.

config ETH0_GATEWAY
	string "Default gateway of management port (eth0)"
	default "192.168.1.1"
	help
	  Default gateway of management port (eth0). Please note that
	  wrong gateway address will generate a runtime error on the switch.

endmenu

choice
	prompt "Hostname source"
	default HOSTNAME_DHCP

config HOSTNAME_DHCP
	bool "Get hostname via DHCP"
	help
	  Get hostname from DHCP server.

config HOSTNAME_STATIC
	bool "Use static hostname"
	help
	  Use static Hostname stored in CONFIG_HOSTNAME_STRING

endchoice

config HOSTNAME_STRING
	string "Static hostname of the switch"
	default "wrs"
	depends on HOSTNAME_STATIC
	help
	  Use this string as a static hostname of the switch.

menu "Authorization and authentication"

config ROOT_ACCESS_DISABLE
	bool "Disable root access via ssh"
	help
	  Used by ssh

config LDAP_ENABLE
	bool "Enable LDAP authorization"
	default n
	help
	  Enable LDAP authorization. Used by ssh.

config LDAP_SERVER
	string "LDAP server"
	depends on LDAP_ENABLE
	help
	  LDAP server(s) e.g. ldap://xldap.cern.ch

config LDAP_SEARCH_BASE
	string "LDAP search base"
	depends on LDAP_ENABLE
	help
	  LDAP search base e.g. dc=cern,dc=ch

choice
	prompt "LDAP filter"
	depends on LDAP_ENABLE
	default LDAP_FILTER_NONE

config LDAP_FILTER_NONE
	bool "Don't apply filter to LDAP"
	help
	  Allow all LDAP users to log in.

config LDAP_FILTER_EGROUP
	bool "Apply e-group filter to LDAP"
	help
	  Allow logins only from an e-group defined in CONFIG_LDAP_FILTER_EGROUP_STR
	  This option is CERN specific.

config LDAP_FILTER_CUSTOM
	bool "Apply custom filter to LDAP"
	help
	  Provide custom filtering string for LDAP authorization.

endchoice

config LDAP_FILTER_EGROUP_STR
	string "LDAP e-group"
 	depends on LDAP_FILTER_EGROUP
	help
	  LDAP's e-group for authorization. This option is CERN specific.

config LDAP_FILTER_CUSTOM_STR
	string "LDAP access filter string"
	depends on LDAP_FILTER_CUSTOM
	help
	  Custom string with a filter for LDAP authorization:
	  (memberOf=CN=white-rabbit-switch-root,OU=e-groups,OU=Workgroups,DC=cern,DC=ch)

choice
	prompt "Authentication method"
	depends on LDAP_ENABLE
	default AUTH_KRB5

config AUTH_LDAP
	bool "Enable LDAP authentication"
	depends on LDAP_ENABLE
	help
	  Used by ssh for authentication

config AUTH_KRB5
	bool "Enable Kerberos authentication"
	depends on LDAP_ENABLE
	help
	  Used by ssh for authentication

endchoice

config AUTH_KRB5_SERVER
	string "Kerberos server"
 	depends on AUTH_KRB5
	help
	  Server name of Kerberos. Usually it is in capital letters.
	  For CERN, please use CERN.CH

menu "Root Password"


config ROOT_PWD_IS_ENCRYPTED
	bool "Should this file include an encripted root password?"
	help
	  The root password, as set here, can be in clear text or
	  encrypted. If it is specified as clear text, it is encrypted and
	  stored in the switch at run time.  If it specified in pre-encrypted
	  form, the string will just be copied in place. A clear-text
	  password in dot-config is less safe against sniffers.

config ROOT_PWD_CLEAR
	string "The password to be used at run time"
	depends on !ROOT_PWD_IS_ENCRYPTED
	default ""
	help
	  The string to be encrypted at boot time by the switch itself,
	  to later use normal ssh authentication. The empty string is
	  allowed.

config ROOT_PWD_CYPHER
	string "The password to be used at run time"
	depends on ROOT_PWD_IS_ENCRYPTED
	help
	  The actual pre-encrypted string. This is stored at run time
	  into /etc/passwd, for ssh authentication. To create the
	  string, please run "mkpasswd --method=md5 <password>"

endmenu

endmenu # "Authorization and authentication"


config DNS_SERVER
	string "static IP address of local DNS server (empty for none)"
	help
	  Using names instead of IP addresses is sometimes handy. This
	  option allow to specify a static server name, that is stored
	  in /etc/resolv.conf, within the WRS image being built. If
	  the string is empty, /etc/resolv.conf is managed according
	  to buildroot defaults.

config DNS_DOMAIN
	string "Default domain for DNS resolution"
	help
	  If CONFIG_DNS_SERVER is being used, this option may be
	  useful as well.

config LOCAL_SYSLOG_FILE
	string "Store WRS syslog messages locally "
	default "/tmp/syslog"
	help
	  Select file to which syslog messages will be stored. 
	  The file is rotated when reaching 1MB. If remote
	  server is specified, the messages go to both, server and local file.

config REMOTE_SYSLOG_SERVER
	string "Send WRS syslog messages to this remote host"
	help
	  This IP address or name, if not empty enables remote syslog
	  in the switch; all messages are sent to this specific host.

config REMOTE_SYSLOG_UDP
	bool "Use UDP for syslog messages"
	default y
	help
	  Select UDP to send system logs. If not set, TCP is used.

config WRS_LOG_HAL
	string "Logging directions for the WR hal"
	default "default_syslog"
	help
	  The string can be:
	  - a pathname (e.g. /dev/kmsg), or
	  - a <facility>.<level> specification like "daemon.debug", or
	  - "default_syslog", or 
	  - an empty string
	  An empty string is used to represent no logging (like /dev/null).
	  When the string is "default_syslog", messages are sent to syslog with
	  the <facility>.<level> inherited from the messages (if not specified
	  in the message, daemon.info is used by default).
	  When the string is "<facility>.<level>", all messages produced by
	  the WR HAL if  syslog is configured will be passed to the syslog at 
	  the same  <facility>.<level>, no matter of verbosity of a message.
	  Please note that unknown facility names will generate a runtime error
	  on the switch.

config WRS_LOG_LEVEL_HAL
	string "Logging verbosity level for the WR HAL"
	default ""
	help
	  Specify verbosity of WR HAL as a string or number. The following
	  levels are supported:
	  ALERT (1)
	  ERROR (3)
	  WARNING (4)
	  INFO (6)
	  DEBUG (7)
	  By leaving this item empty, HAL will use its default verbosity level
	  (INFO).
	  Please note that all messages produced by the WR HAL if syslog is
	  configured will be passed to the syslog at the same
	  <facility>.<level>, no matter of verbosity of a message.

config WRS_LOG_RTU
	string "Logging directions for the RTU daemon"
	default "default_syslog"
	help
	The string can be:
	  - a pathname (e.g. /dev/kmsg), or
	  - a <facility>.<level> specification like "daemon.debug", or
	  - "default_syslog", or 
	  - an empty string
	  An empty string is used to represent no logging (like /dev/null).
	  When the string is "default_syslog", messages are sent to syslog with
	  the <facility>.<level> inherited from the messages(if not specified
	  in the message, daemon.info is used by default).
	  When the string is "<facility>.<level>", all messages produced by
	  the RTU if  syslog is configured will be passed to the syslog at 
	  the same  <facility>.<level>, no matter of verbosity of a message.
	  Please note that unknown facility names will generate a runtime error
	  on the switch.

config WRS_LOG_LEVEL_RTU
	string "Logging verbosity level for the RTU daemon"
	default ""
	help
	  Specify verbosity of RTU daemon as a string or number. The following
	  levels are supported:
	  ALERT (1)
	  ERROR (3)
	  WARNING (4)
	  INFO (6)
	  DEBUG (7)
	  By leaving this item empty, RTU daemon will use its default verbosity
	  level (INFO).
	  Please note that all messages produced by RTU daemon if syslog is
	  configured will be passed to the syslog at the same
	  <facility>.<level>, no matter of verbosity of a message.

config WRS_LOG_PTP
	string "Logging directions for the PTP server (ppsi)"
	default "daemon.info"
	help
	  The string can be a pathname (e.g. /dev/kmsg) or a <facility>.<level>
	  spefification like "daemon.debug". An empty strings is used
	  to represent no logging (like /dev/null).  Please note that
	  unknown facility names will generate a runtime error on the switch.
	  Please note that all messages produced by PPSi if syslog is
	  configured will be passed to the syslog at the same
	  <facility>.<level>, no matter of verbosity of a message.

config WRS_LOG_LEVEL_PTP
	string "Logging verbosity level for the PTP server (ppsi)"
	default ""
	help
	  Specify verbosity of PPSi daemon as a string. This string will be
	  passed to the PPSI after "-d" parameter. Please refer to the PPSI's
	  documentation for more details.
	  By leaving this item empty, PPSi daemon will use its default
	  verbosity level.
	  Please note that all messages produced by PPSi if syslog is
	  configured will be passed to the syslog at the same
	  <facility>.<level>, no matter of verbosity of a message.

config WRS_LOG_SNMPD
	string "Logging directions for the SNMP daemon"
	default "Swd"
	help
	  The string can be a pathname (e.g. /dev/kmsg) or a valid snmpd log
	  option (without -L). "Swd" will forward messages with priority at
	  least warning to syslog with daemon as facility. To set level (i.e. 5)
	  use "S 5 daemon". For details please check "man snmpcmd". An empty
	  strings is used  to represent no logging (like /dev/null). Please
	  note that unknown facility names will generate a runtime error on the
	  switch. NOTE: It looks like Notice is not a default logging priority
	  as writen in manual.

config WRS_LOG_MONIT
	string "Logging directions for the monit"
	default "syslog"
	help
	  The string can be a pathname (e.g. /dev/kmsg) or a "syslog" string.
	  An empty strings is used  to represent no logging. If it is needed to
	  select facility and level please leave here empty string and change
	  /etc/monitrc file directly.
	  Please note that unknown facility names will generate a runtime error
	  on the switch.

config WRS_LOG_OTHER
	string "Logging directions for other programs"
	default "default_syslog"
	help
	  Redirect output from other programs.
	  In the current version following programs uses this option:
	  --wrs_watchdog
	  --wrs_auxclk
	  --wrs_custom_boot_script.sh
	  --vlan.sh
	  This collective entry is to avoid number of entries in dot-config.
	  The string can be:
	  - a pathname (e.g. /dev/kmsg), or
	  - a <facility>.<level> specification like "daemon.debug", or
	  - "default_syslog", or 
	  - an empty string
	  An empty string is used to represent no logging (like /dev/null).
	  When the string is "default_syslog", messages are sent to syslog with
	  the <facility>.<level> inherited from the messages (if not specified
	  in the message, daemon.info is used by default).
	  When the string is "<facility>.<level>", all messages produced by
	  the programs if  syslog is configured will be passed to the syslog at
	  the same  <facility>.<level>, no matter of verbosity of a message.
	  Please note that unknown facility names will generate a runtime error
	  on the switch.

config WRS_LOG_LEVEL_OTHER
	string "Logging verbosity level for other programs"
	default ""
	help
	  Specify verbosity of other programs as a string or number. The
	  following levels are supported:
	  ALERT (1)
	  ERROR (3)
	  WARNING (4)
	  INFO (6)
	  DEBUG (7)
	  By leaving this item empty, other programs daemon will use their
	  default verbosity level (INFO).
	  Please note that all messages produced by other programs if syslog is
	  configured will be passed to the syslog at the same
	  <facility>.<level>

endmenu



menu "Global PTP configuration (profile, timing mode, BMCA and external port config, ...)"


choice
	prompt "PTP Profile"
	default GLOBAL_PROFILE_HA_WR
	config GLOBAL_PROFILE_PTP
		bool "Default (IEEE 1588)"
		help
		  Use the default PTP profile.
	config GLOBAL_PROFILE_HA_WR
		bool "White Rabbit / High-Accuracy (IEEE 1588)"
		help
		  Use the White Rabbit or the High Accuracy profile.
	config GLOBAL_PROFILE_CUSTOM
		bool "Custom Profile"
		help
		  Use the custom PTP Profile. It allows setting values with
		  less constraints.
endchoice

choice
	prompt "BMCA"
	default PTP_OPT_BMCA_STANDARD
	help
	  Select Alternate Best Master Clock Algorithm
	config PTP_OPT_BMCA_STANDARD
		bool "Default IEEE 1588"
		help
		  Use the Alternate Best Master Clock Algorithm as defined in
		  IEEE 1588.
	config PTP_OPT_BMCA_EXT_PORT_CONFIG
		bool "External Port Configuration (disable BMCA)"
		help
		  This option is to force the port state. When set, BMCA is
		  disabled.
		  For more details please refer to the IEEE 1588-2019 (clause 17.6.2)

endchoice

choice
	prompt "Timing Mode"
	default TIME_BC

config TIME_GM
	bool "Grand-Master"
	help
	  This options selects the White Rabbit Switch as a grandmaster,
	  i.e. it uses its input channels to track an Atomic or GPS and
	  claim to be a PTP authoritative source on the network.
	  The clockClass is set to 6 which designates a clock that is
	  synchronized to a primary reference time source.

config TIME_ARB_GM
	bool "Arbitrary Grand-Master"
	help
	  This options selects the White Rabbit Switch as a grandmaster,
	  i.e. it uses its input channels to track an application-specific 
	  source of time.
	  The clockClass is set to 13 which designates a clock that is
	  synchronized to an application-specific source of time. The timescale
	  distributed is then ARB (arbitrary).

config TIME_FM
	bool "Free-Running Master"
	help
	  The White Rabbit Switch pretends to be a master on his PTP
	  network, but it doesn't sync to an external source. Its own
	  internal clocks and counters are used to drive timing.
	  The clockClass is set to 193 and all ports must be set to
	  master-only mode.


config TIME_BC
	bool "Boundary Clock"
	help
	  The White Rabbit Switch is a normal PTP Boundary Clock: it is
	  slave on one of its ports and master on the other ones, according
	  to the standard Best Master Clock algorithm.
	  The clockClass is set to 248 which is the default clockClass.

config TIME_CUSTOM
	bool "Custom"
	help
	  This custom mode allows free access to the clock quality parameters.

endchoice




config PTP_OPT_PTP_VERSION_OVERWRITE
	boolean "Allow the overwrite of the default PTP version per instance"
	default n
	help
	  This option is required to overwrite the PTP version used in
	  the transmitted PTP messages. The actual setting is done in
	  the per instance configuration menu.
	  If this option is not set, the PTP version is set based on the used
	  extension (not profile!).
	  If no extension or HA/L1Sync is used, PTP version is set to
	  v2.1 (IEEE1588-2019).
	  If WR extension is used then PTP version is set to
	  v2.0 (IEEE1588-2008).

config PTP_OPT_OVERWRITE_ATTRIBUTES
	boolean "Overwrite default values of PTP attributes"
	depends on ! TIME_CUSTOM
	default FALSE
	help
	  This option allows to overwrite the default value depending 
	  of the timing mode for the clock accuracy, the clock Allan variance.

config PTP_OPT_DOMAIN_NUMBER
	int "domain-number" if PTP_OPT_OVERWRITE_ATTRIBUTES || TIME_CUSTOM
	default 0
	range 0 255
	help
	  A domain consists of one or more PTP devices communicating with each
	  other as defined by the PTP protocol. A domain defines the scope of
	  PTP message communication, state, operations, data sets, and
	  timescale. PTP devices may participate in multiple domains.
	  For more details please refer to the IEEE 1588-2019 standard.

config PTP_OPT_PRIORITY1
	int "priority1" if PTP_OPT_OVERWRITE_ATTRIBUTES || TIME_CUSTOM
	default 128
	range 0 255
	help
	  A user configurable designation that a clock belongs to an ordered
	  set of PTP devices from which a PTP Master is selected.
	  For more details please refer to the IEEE 1588-2019 standard

config PTP_OPT_PRIORITY2
	int "priority2" if PTP_OPT_OVERWRITE_ATTRIBUTES || TIME_CUSTOM
	default 128
	range 0 255
	help
	  A user configurable designation that provides finer grained ordering
	  among otherwise equivalent PTP devices.
	  For more details please refer to the IEEE 1588-2019 standard

config PTP_OPT_CLOCK_ACCURACY
	int "clock-accuracy" if PTP_OPT_OVERWRITE_ATTRIBUTES || TIME_CUSTOM
	default 33  if TIME_GM || TIME_ARB_GM
	default 32  if TIME_FM
	default 254
	range 0 255
	help
	  An attribute defining the accuracy of the Local Clock (e.g. local
	  oscillator) of a Boundary Clock or Ordinary Clock.
	  For more details please refer to the IEEE 1588-2019 standard.

config PTP_OPT_CLOCK_ALLAN_VARIANCE
	int "clock-allan-variance/offsetScaledLogVariance" if PTP_OPT_OVERWRITE_ATTRIBUTES || TIME_CUSTOM
	default 47360 if TIME_GM || TIME_ARB_GM
	default 50973 if TIME_FM
	default 65535
	range 0 65535
	help
	  An attribute defining the stability of the Local Clock of a
	  Boundary Clock or Ordinary Clock.
	  For more details please refer to the IEEE 1588-2019 standard.

config PTP_OPT_TIME_SOURCE
	int "time-source" if (!TIME_BC) && (PTP_OPT_OVERWRITE_ATTRIBUTES || TIME_CUSTOM)
	default 32 if TIME_GM || TIME_ARB_GM
	default 160 if TIME_FM
	default 160
	range 0 255
	help
	  This information-only attribute indicates the source of time used
	  by the grandmaster (or free-running master).

config PTP_OPT_CLOCK_CLASS
	int "clock-class" if TIME_CUSTOM
	default 6 if TIME_GM
	range 6 6 if TIME_GM
	default 13 if TIME_ARB_GM
	range 13 13 if TIME_ARB_GM
	default 193 if TIME_FM
	range 193 193 if TIME_FM
	default 248 if TIME_BC
	range 248 248 if TIME_BC
	default 248 if TIME_CUSTOM
	range 1 255 if TIME_CUSTOM
	help
	  An attribute defining the TAI traceability, synchronization state and
	  expected performance of the time or frequency distributed by a
	  Boundary Clock or Ordinary Clock.
	  For more details please refer to the IEEE 1588-2019 standard.

endmenu #"PPSI options"

menu "Port PTP/Timing configuration"

choice
	prompt "PTP Port Assignment"
	default PTP_PORT_PARAMS
	help
	  You can choose either to use parameters defined in PORTxx_INSTxx or
	  your own custom configuration file placed in switch file system
	  or downloaded at boot time.

config PTP_PORT_PARAMS
	bool "Generate ppsi.conf based on the PORTxx_INSTyy_z parameters"
	help
	  Generate ppsi.conf based on "PORTxx_INSTyy_z parameters" and "role" specified for each
	  port.
	  PPSI's global settings can be set in file /wr/etc/ppsi-pre.conf

config PTP_CUSTOM
	bool "Custom ppsi.conf in the WRS file system"
	help
	  Use custom file for ppsi defined by CONFIG_PTP_CUSTOM_FILENAME.

config PTP_REMOTE_CONF
	bool "Download ppsi.conf from the network at each boot"
	help
	  This choice allows to specify an URL so you can download a
	  custom file using the network. This allows running a bunch
	  of switches, all with the same configuration but different
	  configurations that can't just be derived from PORT_PARAMS above.

endchoice

config PTP_CUSTOM_FILENAME
	string "Pathname for your custom ppsi.conf"
	depends on PTP_CUSTOM
	default "/wr/etc/ppsi-custom.conf"
	help
	  This is the filename used as ppsi.conf. Please note that the
	  file is copied to /etc/ppsi.conf when configuration is applied,
	  and the PTP daemon always picks /etc/ppsi.conf, not this
	  filename.

config PTP_CONF_URL
	depends on PTP_REMOTE_CONF
	string "Download URL (http, ftp, tftp) for custom ppsi.conf"
	help
	  Like CONFIG_DOTCONF_URL, this option allows passing HOSTNAME, IPADDR
	  and MACADDR in the filename, and if a DNS server is configured,
	  you can use host names.
	  For example: tftp://morgana/wrs-IPADDR-ppsi.conf

source Kconfig_port_timing.in

endmenu # "Port PTP/Timing configuration"

source Kconfig_sfp_fiber.in

menu "PPS generation"
	
config PPSGEN_PTP_FALLBACK
	bool "PTP fallback"
	default N
	help
	  This option enables the PPS generation if a slave instance 
	  programmed to use an extension protocol (WR, L1Sync, ...) is falling back
	  to PTP communication only. 
	
config PPSGEN_PTP_THRESHOLD_MS
	int "PTP threshold (ms)"
	default 500
	range 1 1000
	help
	  This option defines the threshold corresponding to the offset from the 
	  master used to start the generation of the PPS. It is  either used by a PTP slave 
	  instance or a instance using a protocol extension but going into the fallback PTP mode 
	  and with the PTP fallback option active. 
	  A 0 value means that the PPS will be not generated for the considered cases. 
	  When the PPS is generated, it can be also disabled when the offset from master becomes greater
	  than the threshold value + 20%
	
config PPSGEN_GM_DELAY_TO_GEN_PPS_SEC
	int "Grand Master delay for PPS (sec)"
	default 0
	range 0 1000
	help
		This option allows a boundary/ordinary clock to generate PPS when it becomes Grand Master (GM) by BMCA. Becoming GM
		by BMCA might be a transitory situation during a network discovery. The PPS must be activated only when all this 
		transitory phase is terminated. This option then allows to define a delay in seconds to respect before 
		generating the PPS when a GM by BMCA is detected.  
		A 0 value desactivate this feature.

config PPSGEN_FORCE
	bool "Force generation of PPS all the time (not for FR)"
	depends on !TIME_FM
	default n
	help
	  This option enables the PPS generation all the time in various modes
	  except Free-Running Master.

config PPSGEN_FR_ON_SYNC_ONLY
	bool "In FR mode generate PPS only when synchronized to master"
	depends on TIME_FM
	default n
	help
	  If device is configured as Free-Running master, generate PPS only
	  when synchronized to another master. Otherwise PPS is generated all
	  the time."

config EXT_PPS_LATENCY_PS
	int "Compensate signal skew between PPS IN and PPS OUT (in ps)"
	depends on TIME_GM || TIME_ARB_GM || TIME_CUSTOM
	default "0"
	help
	  If one needs to precisely align 1-PPS output with 1-PPS input when WRS
	  works as GrandMaster, calibration are needed to overcome the signal
	  skew between the 1-PPS input and 10MHz clock input. As the component
	  variance of different clock source and WRS, this latency parameter
	  should be calibrated one by one to achieve PPS alignment with high
	  accuracy.
	  The entered value is in ps.

endmenu

menu "Management configuration"
config SNMP_SYSCONTACT
	string "System contact reported by SNMP"
	help
	  If not empty, this value will be reported as System contact
	  (SNMPv2-MIB::sysContact.0)

config SNMP_SYSLOCATION
	string "System location reported by SNMP"
	help
	  If not empty, this value will be reported as System Location
	  (SNMPv2-MIB::sysLocation.0)

config SNMP_TRAPSINK_ADDRESS
	string "Static IP address or name where to send SNMPv1 traps"
	help
	  If not empty, the address or name is ussed as "trapsink"
	  destination in the SNMP configuration file for the switch.
	  It empty, no v1 traps are generated. If both this and
	  the following TRAP2SINK_ADDRESS are set, snmpd sends two
	  traps (one per protocol version). Trapcommunity is "public"
	  (not configurable so far).

config SNMP_TRAP2SINK_ADDRESS
	string "Static IP address or name where to send SNMPv2c traps"
	help
	  If not empty, the address or name is ussed as "trap2sink"
	  destination in the SNMP configuration file for the switch.
	  It empty, no v2c traps are generated. Trapcommunity is "public"
	  (not configurable so far).

config SNMP_RO_COMMUNITY
	string "Read-only community name for SNMP V1/V2 management"
	default "public"
	help
	  If not empty, the 'community' name is a sort of password,
	  that travels as clear text (we don't support encrypted SNMPv3
	  yet). The default is good for testing, but should be changed
	  for production. Please note, however, that the switch processes
	  SNMP only on the CPU Ethernet port (the copper "management" port).

config SNMP_RW_COMMUNITY
	string "Read-write community name for SNMP V1/V2 management"
	default "private"
	help
	  If not empty, the 'community' name is a sort of password,
	  that travels as clear text (we don't support encrypted SNMPv3
	  yet). The default is good for testing, but should be changed
	  for production. Please note, however, that the switch processes
	  SNMP only on the CPU Ethernet port (the copper "management" port).

config SNMP_TEMP_THOLD_FPGA
	int "Threshold level for FPGA temperature"
	default "80"
	help
	  Threshold level for FPGA temperature, when exceeded warning is
	  notified by SNMP via WR-SWITCH-MIB::wrsTemperatureWarning
	  Require hal restart after change

config SNMP_TEMP_THOLD_PLL
	int "Threshold level for PLL temperature"
	default "80"
	help
	  Threshold level for PLL temperature, when exceeded warning is