Changes after rehearsing with team mates

presentations/WR_Javier_WRWS2017_Intro/wr_workshop_2017_intro.tex

@@ -204,6 +204,7 @@ Rabbit\hspace{6em}\insertframenumber/\inserttotalframenumber]{White
       \item Layer 1 syntonization
       \item Digital Dual Mixer Time Difference (DDMTD)
       \item Link delay model
+      \item WR-PTP (backward-compatible extension of PTP)
     \end{itemize}
   \end{block}
 \end{frame}
@@ -299,19 +300,19 @@ Rabbit\hspace{6em}\insertframenumber/\inserttotalframenumber]{White
   \end{center}
 \end{frame}
 
-% \begin{frame}{Digital Dual Mixer Time Difference}{DDMTD}
+\begin{frame}{Digital Dual Mixer Time Difference}{DDMTD}
 
-%   \begin{itemize}
-%     \item Used for precise phase measurements
-%     \item Implemented in FPGA and SoftPLL
-%     \item 62.5MHz WR clock and N=14 results in 3.814kHz output signals
-%   \end{itemize}
-%   \vspace{-0.2cm}
-%   \begin{center}
-%   \includegraphics[width=\textwidth]{misc/dmtd_2N.pdf}
-%   \end{center}
+  \begin{itemize}
+    \item Used for precise phase measurements
+    \item Implemented in FPGA and SoftPLL
+    \item 62.5MHz WR clock and N=14 results in 3.814kHz output signals
+  \end{itemize}
+  \vspace{-0.2cm}
+  \begin{center}
+  \includegraphics[width=\textwidth]{misc/dmtd_2N.pdf}
+  \end{center}
 
-% \end{frame}
+\end{frame}
 
 % %\begin{frame}{Deglitching algorithm -- to backup slides?}
 % %\end{frame}
@@ -368,13 +369,13 @@ Rabbit\hspace{6em}\insertframenumber/\inserttotalframenumber]{White
   \end{center} 
 \end{frame}
 
-\begin{frame}{Simplified block diagram of the gateware}
-  \begin{center}
-    \begin{adjustwidth}{-1.5em}{-1.5em}
-      \includegraphics[width=1.1\textwidth]{switch/switch_hdl_simple.pdf}
-    \end{adjustwidth}
-  \end{center}
-\end{frame}
+% \begin{frame}{Simplified block diagram of the gateware}
+%   \begin{center}
+%     \begin{adjustwidth}{-1.5em}{-1.5em}
+%       \includegraphics[width=1.1\textwidth]{switch/switch_hdl_simple.pdf}
+%     \end{adjustwidth}
+%   \end{center}
+% \end{frame}
 
 
 \begin{frame}{WR Node: SPEC board}

presentations/WR_Javier_WRWS2017_high_precision/wr_workshop_2017_high_precision.tex

@@ -164,6 +164,16 @@ $ E(s) = 1 - H(s) = \frac{s}{s + K_{VCO} K_d F(s)} $
 \includegraphics[height=0.7\textwidth]{misc/pll_psd.pdf}
 }
 
+\begin{frame}{How to drive the phase noise PSD curve down?}
+ \begin{block}{Medium and high (Fourier) frequencies}
+   Easy! Just buy a better oscillator. OCXO-based WR node in
+   development at CERN achieves 100fs jitter (100Hz-5MHz).
+ \end{block}
+ \begin{block}{Low (Fourier) frequencies}
+  Tricky. Usually involves serious architectural changes. See later.
+ \end{block}
+\end{frame}
+
 \section{White Rabbit case}
 \subsection{}
 \begin{frame}{WR time transfer performance: basic test setup}
@@ -182,15 +192,6 @@ $ E(s) = 1 - H(s) = \frac{s}{s + K_{VCO} K_d F(s)} $
 
 \end{frame}
 
-\begin{frame}{How to drive the phase noise PSD curve down?}
- \begin{block}{Medium and high (Fourier) frequencies}
-  Easy! Just buy a better oscillator. OCXO-based node in development
-  at CERN achieves 100fs jitter (100Hz-5MHz).
- \end{block}
- \begin{block}{Low (Fourier) frequencies}
-  Tricky. Usually involves serious architectural changes. See next.
- \end{block}
-\end{frame}
 
 \begin{frame}{Digital Dual Mixer Time Difference}{DDMTD}
   \begin{itemize}
@@ -204,7 +205,7 @@ $ E(s) = 1 - H(s) = \frac{s}{s + K_{VCO} K_d F(s)} $
   \end{center}
 \end{frame}
 
-\begin{frame}{Daughterboard Test Setup}
+\begin{frame}{Test setup for 10MHz switch output}
   \begin{center}
     \includegraphics[width=\textwidth]{measurements/WRSlowJitter/rsz_experimental_setup.png}
   \end{center}
@@ -248,17 +249,6 @@ $ E(s) = 1 - H(s) = \frac{s}{s + K_{VCO} K_d F(s)} $
   \end{center}
 \end{frame}
 
-\begin{frame}{Test Results in Slave mode: PM noise}
-  \begin{center}
-    \includegraphics[height=.85\textheight]{measurements/WRSlowJitter/slave_pn.png}
-  \end{center}
-\end{frame}
-
-\begin{frame}{Test Results in Slave mode: Modified ADEV}
-  \begin{center}
-    \includegraphics[height=.85\textheight]{measurements/WRSlowJitter/slave_mdev.png}
-  \end{center}
-\end{frame}
 
 \begin{frame}{Need more information?}
   \begin{center}