Skip to content

News · Changes

Page history
orson_admin created page: News authored by Projects's avatar Projects
Show whitespace changes
Inline Side-by-side
News.md 0 → 100644
View page @ ac25e3ab
## SPEC Fan design files released
_added by Tomasz Wlostowski on 2015-03-30 10:35:16.367652_
We have released the official documentation for the mezzanine cooling
fan designed to fit the SPEC board. The fan design is described on this
[page](Fan-Design).
## 18-12-13: Labview drivers for SPEXI and SPEC
_added by Erik van der Bij on 2013-12-18 10:53:20.579823_
The company INCAA has written Labview drivers for the [FMC
DEL 1ns 4cha](https://www.ohwr.org/project/fmc-delay-1ns-8cha/wiki) and
[FMC TDC 1ns 5cha](https://www.ohwr.org/project/fmc-tdc/wiki) mezzanine
cards. These drivers work both for the PCIe-based [SPEC
carrier](https://www.ohwr.org/project/spec/wiki) and PXIe-based [SPEXI
carrier](https://www.ohwr.org/project/spexi/wiki) board.
The [source code of the drivers](https://www.ohwr.org/documents/307) is
available under the GPL license.
## 16-01-2013: Production test improved
_added by Erik van der Bij on 2013-01-16 08:42:56.378239_
Open Hardware doesn't stop at just having a good hardware design. We at
CERN believe it is also important to provide a good production test
system with the hardware to ease the manufacturing process. For this we
have set up a testing environment, called
[PTS](https://www.ohwr.org/pts/wiki).
The SPEC board also has a range of tests that can run in the PTS
environment that has been used to test the cards after production. The
company [Seven
Solutions](https://www.ohwr.org/companies/seven-solutions) has just
improved the Production Test Suite (PTS) of the SPEC board so that now
all memory addresses lines are tested and that boards will not signalled
to be defective while they actually are OK. Also the speed of testing
has improved. Companies producing the SPEC board should take the latest
version out of the [PTS
repository](https://www.ohwr.org/project/pts/tree/master/test/spec).
The files that have been modified are:
- test/spec/python/gn4124.py (so that this DMA library automatically
configures the Interrupt enable mask register)
- test/spec/python/test07.py (so that all the address lines are
checked and the test procedure is accelerated)
- test/spec/firmware/test07.bin (to correct the intermittent-error
generation)
## 03-07-2012: Delivery of 52 SPEC boards
_added by Erik van der Bij on 2012-07-03 16:21:15.879106_
It's getting serious now as we received at CERN four boxes with in total
52 SPEC boards from the company [Seven
Solutions](https://www.ohwr.org/companies/seven-solutions). All boards
are individually packed and have an LHC barcode on it that will ease us
entering the cards in our equipment database.
These boards will be used together with
[ADC](https://www.ohwr.org/project/fmc-adc-100m14b4cha/wiki), [Fine
Delay](https://www.ohwr.org/project/fmc-delay-1ns-8cha/wiki) and
[digital I/O](https://www.ohwr.org/project/fmc-dio-5chttla/wiki)
mezzanines, often in combination with firmware supporting [White
Rabbit](https://www.ohwr.org/white-rabbit/wiki) and therefore giving
precise time stamping of data.
## 12-06-2012: SPEC passes EMC tests
_added by Erik van der Bij on 2012-06-12 17:29:06.110610_
The SPEC board together with a 5 channel Digital I/O card have passed
the most restrictive EMC tests of each class (domestic and industrial)
successfully:
- EM Radiated Emission: Class B (Domestic) EN 55022 (2006) / A1 (2007)
- EM Immunity (Industrial): EN 61000-4-3 (2006) / A1 (2008) / A2
(2010), EN 61000-4-4 (2004) / A1 (2010) / Corr (2010), EN 61000-4-6
(2009), EN
61000-4-2 (2009), EN 61000-4-8 (2010).
The [test report](https://www.ohwr.org/project/spec/wikis/Documents/EMC-Test-report) is publicly
available.
## 25-04-2012: SPEC boards running in Siberia!
_added by Erik van der Bij on 2012-04-25 14:52:14.162164_
First field tests of two SPEC boards running a White Rabbit timing link
between them have been made in Siberia. These tests are made by DESY to
verify the usability of the board at the Gamma-Ray and Cosmic-Ray
experiment
[HiSCORE-EA](http://tunka-hrjrg.desy.de/e98279/index_eng.html) at the
Tunka site. Full results of the tests will be made available soon. Two
kilometres of fibre where outside, while the SPEC boards were nicely
warm inside the counting room.
## 05-01-2012: 70 SPEC cards produced in 2011
_added by Erik van der Bij on 2012-01-05 13:32:24.681807_
In the year 2011 the company
[Creotech](https://www.ohwr.org/companies/creotech) has produced and
sold fifty SPEC boards. With the twenty cards from the pre-production of
the seventy that CERN has ordered from the company [Seven
Solutions](https://www.ohwr.org/companies/seven-solutions), in total
seventy SPEC boards have been produced in 2011.
## 11-11-2011: 20 cards commercially produced
_added by Erik van der Bij on 2011-11-11 16:50:16.416408_
The pre-series of the first commercial series production of SPEC cards
has succeeded. After repairing some assembly problem with the FMC
connector, all twenty cards passed the test on the test bench that was
prepared by CERN. The cards will be sent to CERN for a final inspection
before giving the OK to produce another fifty.
## 13-10-2011: CE EMC tests will be made
_added by Erik van der Bij on 2011-10-13 10:22:26.384629_
CERN has placed an order for EMC testing according to EN 55022(2006)
/A1(2007) + EN 55024(1998)/A1 (2001)/A2(2003). Once these tests are
done, it will allow the board to carry the CE approval.
## 26-08-2011: Absolutely ready for production!
_added by Erik van der Bij on 2011-08-26 14:33:29.092379_
The modification for a better mechanical fit has been made and
halogen-PCBs will be ordered to start the first series production of
SPEC boards.
A serious piece of automated test software has been made that will check
all soldered connections on the board and that will measure the
different supply voltages. This is all possible because of the
groundwork done by the [Production Test Suite
project](https://www.ohwr.org/project/pts) software logically called PTS
and the [FMC Carrier
tester](https://www.ohwr.org/project/fmc-conn-tester/wiki) test card
that measures all connections to the FMC connector. We have used these
to create the "PTS for SPEC" production software. The [user
manual](https://www.ohwr.org/project/pts/blob/master/test/spec/doc/TEST_SPEC.pdf)
gives a good overview of the ease of use.
We are now ready to send a complete test bench (PC, SPEC reference card,
FMC test card, cables etc.) to the company that will produce and test 70
boards. First 10 though, just to be sure...
## 22-08-2011: V3 ready, let's go for V4!
_added by Erik van der Bij on 2011-08-22 17:54:09.329196_
The V3 of the design was ready for production on 22 July. We'd like to
produce 70 of those cards of this version, apart from the fact that a
user at GSI just found a mechanical problem that could appear with a
certain combination of SFP plugin and PC type. Being just in time to
correct this by simply moving the SFP 2.5 mm further out on the PCB, we
decided to make a V4 of the PCB.
Why a V4 while the V3 never was produced? As this will ease the
tracibility as possibly copies of this Open Design design may already be
around\!
## 01-07-2011: V2 boards tested
_added by Erik van der Bij on 2011-07-01 17:53:18.152267_
Three V2 boards have been received. One has already passed the full
production suite, two others have only received a very short test (and
passed). This means that this version can be used to start a series
production.
Actually there is still a not-understood issue that we don't manage to
get communication between the two SATA connectors working, while from
each one to the FMC test board works OK. We are currently looking into
that and believe it is only a firmware problem.
## 31-05-2011: Production test software working
_added by Erik van der Bij on 2011-06-01 17:38:26.073429_
For the production of the SPEC cards specific production software has
been written and demonstrated. This software provides a simple go/no-go
interface with logging facilities to easily find production errors. The
software is written in Python and uses a CERN-written test environment
called Bakara. To test the connectivity FMC connector on the SPEC card,
a specific [FMC carrier test
card](https://www.ohwr.org/project/fmc-conn-tester) is developed that is
also able to measure the different power supplies and test the different
gigabit links.
## 13-05-2011: V2 ready. Pre-production boards will be built.
_added by Erik van der Bij on 2011-05-17 10:00:50.554277_
The layout of the V2 of the SPEC board is ready. It is an improvement of
version "1.1". We will build 3 of these pre-production boards before we
will order 70 boards. Two production test benches are being set up.
## 11-05-2011: Design review of V2 held
_added by Erik van der Bij on 2011-05-12 16:54:26.433334_
Five engineers have reviewed version 2 of the SPEC card. Many small
changes have been made to make the board better producable. E.g. instead
of 23 resistor values only 10 will be needed. The production files will
soon be generated by CERN's design office.
## 24-02-2011: Design review of "V1.1" on 1/3/11
_added by Erik van der Bij on 2011-02-24 17:48:43.314040_
The debugging of the SPEC card is going really fine: all active
components are fully tested, and most of the slow connections on the FMC
connectors are tested with the fine delay module.
As there is an urgent request for more SPEC cards, notably for the
development of White Rabbit end nodes by CERN's partners, the team has
been working of solving of all outstanding Issues and making a version
"1.1" of the PCB.
On the first of March we will therefore review the updated schematics
and PCB layout, after which a quick production of ten cards will be
made.
In parallel, the new design will then be verified by CERN's design
office to generate standardised production files. If everything goes
well, it will be these files that will be used for a first production of
around 50 SPEC cards.
## First DMA transfer to/from DDR3
_added by Anonymous on 2011-02-08 14:35:34.866241_
A first DMA transfer to the SPEC DDR3 and back to the host has been done
this morning.
The DDR3 interface seems to work well, but more exhaustive test of the
DDR3 interface are still to be done.
## 19-01-2011: 3 SPEC cards arrived at CERN
_added by Erik van der Bij on 2011-01-19 13:25:06.111342_
Three cards arrived at CERN. After delivery to our offices they will
immediately be powered on.
## 05-11-2010: PCB layout finished. Prototypes by mid December.
_added by Erik van der Bij on 2010-11-08 08:32:28.167585_
After several reviews the PCB layout of the Simple PCIe FMC carrier is
finalised. CERN's design office verified the design and created standard
production files. Three prototype boards will be produced and assembled
in Poland before being sent to CERN by mid December.
## 10-09-2010: PCB layout start
_added by Erik van der Bij on 2010-09-10 14:04:19.329446_
The comments from the schematics review have been taken into account and
PCB layout starts. The aim is to make a low cost 6-layer board (cf. a
12-layer one for the more complex FMC PCIe Carrier - PFC), while paying
much attention to signal quality issues such as signals crossing splits
in the power planes.
## 07-09-2010: Schematics review held
_added by Erik van der Bij on 2010-09-08 17:30:34.872228_
The third schematics review of the Simple PCI Express FMC carrier has
been held. Some improvements and simplifications of the schematics are
required, after which the PCB layout can be started.
## 23-06-2010: Project started
_added by Erik van der Bij on 2010-06-23 13:57:40.541075_
After having seen the complexity of the FMC PCI carrier project, with
its many resources that are likely not used for many applications and
that increase the cost, it has been decided to make a cost optimised
version of this card. The design will be done by a company, with a tight
interaction with CERN. The project will be run with the Open Hardware
paradigm and the design files will be made available via this site.