doc: correct spelling & grammar errors

6f2f2e5c · Benoit Rat · bd64bd24 · 6f2f2e5c
Commit 6f2f2e5c authored Apr 02, 2014 by Benoit Rat
Hide whitespace changes
Inline Side-by-side

Showing with 13 additions and 13 deletions

wr-starting-kit.md doc/wr-starting-kit.md +13 -13

No files found.
--- a/doc/wr-starting-kit.md
+++ b/doc/wr-starting-kit.md
@@ -169,7 +169,7 @@ In this section, we resume the main changes that happens at each release of the
 * Calibration has been improved using t42p procedure


-A detailed changelog can be found on the wiki page of each of of the submodules:
+A detailed changelog can be found on the wiki page of each submodules:

 * [wr-nic-v2.0](http://www.ohwr.org/projects/wr-nic/wiki/Release_v2)
 * [spec-sw-v2014-02](http://www.ohwr.org/projects/spec-sw/wiki#version-2014-02)
@@ -193,7 +193,7 @@ In order to use the white rabbit starting kit and setup the different
 experiments you will need:

 * An oscillocope with at least 150Mhz bandwitdh (500Mhz is recommanded).
-* A PC with with at least two `PCIe x4` ports (`x8` & `x16` are also compatible)
+* A PC with at least two `PCIe x4` ports (`x8` & `x16` are also compatible)
 * The Operative System **Ubuntu LTS 32bit (Long Term Support)** installed.
 * Two mini-USB (B) cables (not provided with the kit).

@@ -678,7 +678,7 @@ has the priority.
 ~~~~~~~~~~

 > ***Warning:***  Be aware that if you try to remove the spec kernel modules with the virtual UART
-activated, your PC will hangs and thus you will need to reboot. You must close
+activated, your PC will hang and thus you will need to reboot. You must close
 the virtual UART before doing this kind of operation.


@@ -972,7 +972,7 @@ ch 4,       542.500000000
 ~~~~~~~~

 > ***Notes:*** If you see other timestampings messages coming from channel 2 this mean you don't
-have disable the PPS mode. Check [Disabling PPS](#disabling-pps-on-channel-2) section.
+have disabled the PPS mode. Check [Disabling PPS](#disabling-pps-on-channel-2) section.


 ### Time stamping input & output.
@@ -1388,7 +1388,7 @@ Connect to the WRS
 If you have a White Rabbit Switch ([WRS]), you should try to see
 the synchronization between the [WRS] and the two [SPEC+FMCDIO] boards.

-First you need to setup the two [SPEC+FMCDIO]s as `slave` by changing the
+First you need to set up the two [SPEC+FMCDIO]s as `slave` by changing the
 mode in the UART of each board.

 ~~~~~{.sh}
@@ -1450,8 +1450,8 @@ wrc# sfp add AXGE-1254-0531 46407 167843 73622176
 wrc# sfp add AXGE-3454-0531 46407 167843 -73622176
 ~~~~~~~~~~~

-Do not forget to also add these value to your other WR equipments (i.e, [WRS])
-as explained in the wiki page.
+Do not forget to also add the proper calibration values to your other
+WR equipments (i.e, [WRS]) as explained in the wiki page.

 You might also check the [wrpc.pdf] for extended explanations on how to run
 yourself the calibration procedure.
@@ -1485,7 +1485,7 @@ input 10MHz signal can be square or sinusoidal.

 ### Example from a FMC fine-delay

-If you have a [FMC fine-delay] board you can generated the PPS/10MHz by
+If you have a [FMC fine-delay] board you can generate the PPS/10MHz by
 executing the following commands (using release 2014.04):

 ~~~~~~{.sh}
@@ -1506,7 +1506,7 @@ wrc# mode gm
 wrc# ptp start
 ~~~~~~~~~~~~~

-And you should obtained:
+And you should obtain:

 ~~~~~~{.sh}
 PLL locking .................. LOCKED
@@ -1533,7 +1533,7 @@ You can also run GM in a full standalone mode in order to transmit WR clock with
 First you need to flash the SPEC with the latest bitstream you can find the package:
 <http://www.sevensols.com/dl/wr-nic/bin/latest_stable.tar.gz>

-To do so you need to generate a MSC file as follow:
+To do so you need to generate a MSC file as follows:

 	Create PROM Files > SPI Flash > Single FPGA > 32M > MCS

@@ -1542,7 +1542,7 @@ the corresponding SPI flash memory: `M25P32`.

 Then:

-* The setup of the cable is exactly the same as above, and you do not need to setup the mode because it is
+* The setup of the cable is exactly the same as above, and you do not need to set up the mode because it is
 correctly configured for GM by default at power up.
 * Then you need to run grandmaster mode from wrc console, as above.
 * (Optional) Finally, if you need to keep this configuration at power up, you can write a small script
@@ -1815,7 +1815,7 @@ Frequently Added Questions
 Online & Updated
 -----------------

-The FAQ is update on a regular basis on the ohwr.org website so
+The FAQ is updated on a regular basis on the ohwr.org website so
 we strongly recommand you to visit the webpage:

 * <http://www.ohwr.org/projects/wr-starting-kit/wiki/FAQ>
@@ -1876,7 +1876,7 @@ After this you should reboot your PC with the new kernel source and start from [
 You should first try to desactivate the termination resistance that can
 consume most of the current if this one is really low.

-Otherwise you should configure the DAC to setup a different threshold, however this option is not actually implemented.
+Otherwise you should configure the DAC to set up a different threshold, however this option is not actually implemented.


 ### The link is down, but everything is connected