Commit 688044a8 authored by Grzegorz Daniluk's avatar Grzegorz Daniluk

presentations/WRS_2014_status: clean-up HW part and move front panel image to figures

parent 65768aad
......@@ -253,11 +253,12 @@
\end{frame}
\section{Hardware}
\subsection{}
\begin{frame}<beamer>{Outline}
\tableofcontents [currentsection]
\end{frame}
\subsection{HW: The new SCB v3.4}
\begin{frame}{\insertsubsectionhead}
\begin{frame}{The new SCB v3.4}
The WRS is now shipped with a SCB v3.4 with the following main changes:\footnote{The WRS v3.4 is still shipped with minibackplane v3.3}
\begin{itemize}
......@@ -267,21 +268,16 @@ The WRS is now shipped with a SCB v3.4 with the following main changes:\footnote
\item PPS input has a configurable 50$\Omega$ configuration.
\item Correct reset signal for \texttt{CDCM61002}.
\end{itemize}
\end{frame}
\begin{frame}{\insertsubsectionhead}
\begin{center}
\includegraphics[height=6.0cm]{front_panel-v34}
\end{center}
\begin{frame}{The new SCB v3.4}
\begin{center}
\includegraphics[width=\textwidth]{switch/front_panel-v34.png}
\end{center}
\end{frame}
\subsection{Release v4.1}
\begin{frame}{\insertsubsectionhead}
\begin{frame}{Release v4.1}
To support the new SCB v3.4 we have created the new release v4.1. It now supports:
......@@ -297,8 +293,7 @@ To support the new SCB v3.4 we have created the new release v4.1. It now support
\end{itemize}
\end{frame}
\subsection{Updating with correct HW info}
\begin{frame}{\insertsubsectionhead}
\begin{frame}{Updating with correct HW info}
\begin{alertblock}{Important}
Since SCB v3.4, hwinfo is saved by manufacturer.
If you want to upgrade from v3.3 to the new v4.1 firmware we suggest you to first update the correct hwinfo.
......@@ -312,31 +307,31 @@ Seven Solutions provides a tarball with the correct hwinfo for all v3.3 switches
\end{frame}
%% Not sure who need to tell or if it is the correct place
\section{Roadmap}
\subsection{Release v4.2}
\begin{frame}{\insertsubsectionhead}
Now that the update procedure is straigh forward we might release more often with fewer changes. %% This will nbe true?
\begin{itemize}
\item Add \texttt{CLK1} \& \texttt{CLK2} 10MHz outputs.
\item Improve the web interface when rebooting.
\item Read SDB from gateware.
\end{itemize}
\end{frame}
\subsection{Release v5.0}
\begin{frame}{\insertsubsectionhead}
\begin{itemize}
\item Update arm kernel to v3.14
\item What else ...?
\end{itemize}
\end{frame}
%\section{Roadmap}
%\subsection{Release v4.2}
%\begin{frame}{\insertsubsectionhead}
%
%Now that the update procedure is straigh forward we might release more often with fewer changes. %% This will nbe true?
%
%\begin{itemize}
% \item Add \texttt{CLK1} \& \texttt{CLK2} 10MHz outputs.
% \item Improve the web interface when rebooting.
% \item Read SDB from gateware.
%\end{itemize}
%\end{frame}
%
%
%\subsection{Release v5.0}
%\begin{frame}{\insertsubsectionhead}
%
%\begin{itemize}
% \item Update arm kernel to v3.14
% \item What else ...?
%\end{itemize}
%\end{frame}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\subsection*{}
\section*{}
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
\begin{frame}{Thank you}
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment