Commit a9bf5a62 authored by Matthieu Cattin's avatar Matthieu Cattin

doc: Add todo list and firmware test plan.

parent c41460ea
- Hardware external rising edge
- Hardware external falling edge
- Hardware internal positive slope
- Hardware internal negative slope
- Hardware internal positive slope, threshold range
- Hardware internal negative slope, threshold range
- Hardware internal on channel 1
- Hardware internal on channel 2
- Hardware internal on channel 3
- Hardware internal on channel 4
- Hardware enable
- Software
- Software enable
- Delay range
- Trigger alignment when decimation factor is > 1
- ADC offset correction
- ADC gain correction
- Decimation range
- Pre-trigger samples range
- Post-trigger samples range
- Total number of samples range (full memory, overlapping, etc...)
- Number of shots range
- Multi-shot mode, memory arrangement
- Multi-shot mode, number of samples range (up to max dpram size)
ADC core CSR:
* Acq and trig LEDs manual control bits => tested with production test03
- Test data (Write the address counter value instead of ADC data to DDR)
! Manual bitslip of adc data serdes => Cannot be tested as automatic bitslip is generated in hdl
- Offset DAC clear
- FMC clock enable
- FSM start command
- FSM stop command
- FSM unused commands (shouldn't do anything)
! FSM state => cannot test all states (e.g. DECR_SHOT lasts only 1 tick)
- SerDes PLL lock status (use FMC clock enable)
! SerDes sync status, must be 1 => cannot test more
* Trigger config, delay and software trigger registers => see Trigger chapter
* Number of shots => see Datapath chapter
* Trigger position => see Datapath chapter
* Decimation rate => see Datapath chapter
* Pre-trigger samples => see Datapath chapter
* Post-trigger samples => see Datapath chapter
- Samples counter
* Channel N control register (switches) => tested with production test08
- Channel N value register (use pattern from ADC)
* Channel N correction gain and offset registers => see Datapath chapter
- Interrupt mask
- DMA done interrupt
? DMA error interrupt => how to force a DMA error
- Trigger interrupt
- End of acquisition interrupt
- Multi-interrupt
- UTC set register
- Coarse set register
- Trigger tag
- Acquisition start tag
- Acquisition stop tag
- Acquisition end tag
Carrier CSR:
* Carrier type => tested in fmc_adc_spec access class
? Carrier PCB revision => how to automate this test?
! FMC mezzanine presence => cannot automated this test
! P2L PLL lock status, must be 1 => cannot test more
! SysClk PLL lock status, must be 1 => cannot test more
! DDR calibration done status, must be 1 => cannot test more
! SPEC LEDs => cannot automated this test
=> carrier specific firmaware parts will be hard to test...
- Remove carrier SPI master -> shift other slaves base addresses.
- Add WR core
1)for time-tags
2)for sampling clock control
- Remove mutli-irq register from interrupt controller.
-> perhaps add counters instead
- Update interface of wbgen2 generated cores (name change).
- Remove unused 250MHz clock signals, buffer
- Unify address inferfaces: put all in bytes (wishbone addr, trig pointer, ...)
-> Change GN4142-core WB bus(es) to byte address.
-> Change DDR-core WB bus(es) to byte address??
- Add error flags (interrupt?): - instead of overwriting memory for a given acquisition.
- if read during acquisition (or even block read during acq?).
- Rename decimation (and "sample rate" register) in under-sampling.
- Use 200MHz clock for WB from ddr-ctrl to gn4124-core.
- Clean-up adc core WB interface to DDR -> use only one clk (=> sys_clk)
- Replace all Xilinx FIFO by generic ones from general-cores lib (! last time I tried, it broke the DMA.).
- License header in every file -> check
- Take data for threshold trigger after offset/gain correction.
- Rename UTC core in time-tagging core or something like that.
- Test sampling clocks from 10MHz to 105MHz.
- Add sampling clock presence flag. Or better a sampling clock frequence register.
- Over-heat and input over-load interrupts??
- Time-tag for every trigger in multi-shot.
- Review reset logic.
- Add Etherbone.
- End acq interrupt generation after a acq stop command ???
- Remove huge files from git repo.
- Make the project ucfgen friendly (if anything has to be done, not sure).
- Include the git tree in a .tar.gz along with the .bin file (in the files section) for each release.
- Remove meta-info field in time-tags?
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment