v2.0
Project | Open issues | State | Due date |
---|---|---|---|
DIOT Igloo2-based radiation-tolerant System Board | 0 | Closed | |
FMC-PROFINET | 1 | Open | |
DIOT Zynq Ultrascale-based System Board | 0 | Closed | |
DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier | 17 | Open | |
RaToPUS radiation-tolerant AC-DC power supply | 1 | Open |
Unstarted Issues (open and unassigned)
19
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Consider adding fuses to RTM power rails
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Add more diagnostics to backplane I2C
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Add crystal oscillator circuit
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Add posibility to program Si5341B from system board
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · QSPI write/read problem from firmware
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Add 16th backplane diff pair
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Dual LEMO connector
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · IRPS5401 BOOT_B/C/D coupling to PHASE_B/C/D - change to 100nF
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · rename P5VREG to P5V_REG
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · TDA21240AUMA1 is obsolete and should be replaced
- FMC-PROFINET · Check the design of components obsolecence
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Front panel LEDs number doesn't match schematic
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Main power supply PMIC can't be turned off due to bad enable logic
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · NCP51145PDR2G is obsolete
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Swapped P12V0 and GND descriptions on top overlay
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Board outline modification
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Missing Boost Diode
- RaToPUS radiation-tolerant AC-DC power supply · 12v-power: TR1 and L7 transformers
- DIOT Kintex Ultrascale-based Peripheral Board FMC Carrier · Change ESD diodes
Ongoing Issues (open and assigned)
0
Completed Issues (closed)
85
- DIOT Igloo2-based radiation-tolerant System Board · Modify powering scheme, move from FEAST and LT3083 to bPOL12V
- DIOT Igloo2-based radiation-tolerant System Board · Replace MURATA DLW5BSN191SQ2L (L1) with DLW5BSM191SQ2L
- DIOT Igloo2-based radiation-tolerant System Board · power cycle pulse generator
- DIOT Igloo2-based radiation-tolerant System Board · Smart Debugger Pins
- DIOT Igloo2-based radiation-tolerant System Board · PGOOD behind I2C Expander
- DIOT Igloo2-based radiation-tolerant System Board · FMC PG_C2M
- DIOT Igloo2-based radiation-tolerant System Board · Use net before shunt resistor for powering the current sense differential amplifier
- DIOT Igloo2-based radiation-tolerant System Board · SERVMOD_DIR pull up/down
- DIOT Igloo2-based radiation-tolerant System Board · FLASH_MISO needs a pull-up
- DIOT Igloo2-based radiation-tolerant System Board · front panel LEDs too short to reach the front panel
- FMC-PROFINET · replace dip-switch component with something smaller than used today
- RaToPUS radiation-tolerant AC-DC power supply · Add relay on AC line driven from the backplane connector.
- RaToPUS radiation-tolerant AC-DC power supply · Replace backplane connector for ACDC stage to Amphenol 51939-1064
- RaToPUS radiation-tolerant AC-DC power supply · Connect PE from power entry socket to the backplane connector and front panel.
- RaToPUS radiation-tolerant AC-DC power supply · Use IEC power entry with line filter
- DIOT Igloo2-based radiation-tolerant System Board · SERVMOD signals going to the backplane should be pulled up (not down) after the voltage translating buffer
- DIOT Igloo2-based radiation-tolerant System Board · add 2nd via to take PPeriph from L1 to L4PWR
- DIOT Igloo2-based radiation-tolerant System Board · some vias are not covered with soldermask
- DIOT Igloo2-based radiation-tolerant System Board · correct GND polygon around IC34
- DIOT Igloo2-based radiation-tolerant System Board · move P2V5_PLL_VSSA polygon to L10 and expand CPCIS_12V polygon around J21
- DIOT Igloo2-based radiation-tolerant System Board · remove v1.0 PcbDoc from the project
- DIOT Igloo2-based radiation-tolerant System Board · Schematics validation reports conflicting harness definitions for FMC-LA_SE
- DIOT Igloo2-based radiation-tolerant System Board · Connect RSTON from nanoFIP to power cycle request circuit
- DIOT Igloo2-based radiation-tolerant System Board · Bpol12V Solder mask layer
- DIOT Igloo2-based radiation-tolerant System Board · sch: remove JTAG selector jumpers drawing
- DIOT Igloo2-based radiation-tolerant System Board · remove IC25 I/O expander
- DIOT Igloo2-based radiation-tolerant System Board · FMC.Sch: use only PGOOD_FMC to drive PG_C2M
- DIOT Igloo2-based radiation-tolerant System Board · unrouted net P12V_SHUNT
- DIOT Igloo2-based radiation-tolerant System Board · Avoid 4-way connections in the schematic
- DIOT Igloo2-based radiation-tolerant System Board · Jumper selection for Igloo2 JTAG
- DIOT Igloo2-based radiation-tolerant System Board · Powering: replace jumper for PPERIPH selection with 0R resistors. P2V5 selected by default
- DIOT Igloo2-based radiation-tolerant System Board · Update Board version resistor net
- DIOT Igloo2-based radiation-tolerant System Board · SERVMOD signal should be translated to P3V3 (not PPERIPH)
- DIOT Igloo2-based radiation-tolerant System Board · review names of signals of DI/OT backplane P1-P6 connectors
- DIOT Igloo2-based radiation-tolerant System Board · Connect reset generated by nanoFIP to DEVRST_N of Igloo2
- DIOT Igloo2-based radiation-tolerant System Board · Replace Dialight 592-2323-302F - it's obsolete
- DIOT Igloo2-based radiation-tolerant System Board · Replace TPS7A4533DCQ with LM317D2TG
- DIOT Igloo2-based radiation-tolerant System Board · Replace Monimod with AD7291 ADC
- DIOT Igloo2-based radiation-tolerant System Board · Replace LT3083
- DIOT Igloo2-based radiation-tolerant System Board · Do not mount crystal Q3 connected to XTLOSC_MAIN_*
- FMC-PROFINET · Ethernet connectors' connection to the carrier front panel for EMC
- RaToPUS radiation-tolerant AC-DC power supply · replace TPS78633DCQ with TPS7A4533
- RaToPUS radiation-tolerant AC-DC power supply · replace OPA2192 with OPA192?
- RaToPUS radiation-tolerant AC-DC power supply · 5v-control: R103 value
- RaToPUS radiation-tolerant AC-DC power supply · 5v-power: missing TVS at the output
- RaToPUS radiation-tolerant AC-DC power supply · 12v-control: +5V power net is not powered
- RaToPUS radiation-tolerant AC-DC power supply · 12v-power: R79 and R80 was decreased to 10k in Lalit's v1.1
- RaToPUS radiation-tolerant AC-DC power supply · connectors: remove *deg* label, we don't use it
- RaToPUS radiation-tolerant AC-DC power supply · connectors: pin D3 should be connected to GND (it's a presence detection pin)
- RaToPUS radiation-tolerant AC-DC power supply · connectors: pin C2 should be left unconnected
- RaToPUS radiation-tolerant AC-DC power supply · connectors: connect *swclk* from monimod to pin C1
- RaToPUS radiation-tolerant AC-DC power supply · connectors: connect *swdio* from monimod to pin B1
- RaToPUS radiation-tolerant AC-DC power supply · connectors: 12V sense signals are swapped
- RaToPUS radiation-tolerant AC-DC power supply · connectors: rename *mm_shdn*
- RaToPUS radiation-tolerant AC-DC power supply · connectors: remove *en* label, we don't use it in RaToPUS
- RaToPUS radiation-tolerant AC-DC power supply · Missing licensing notes
- RaToPUS radiation-tolerant AC-DC power supply · Copper layers thickness
- DIOT Igloo2-based radiation-tolerant System Board · Replace OPA192 with OPA2192ID
- DIOT Igloo2-based radiation-tolerant System Board · Revisit pcb version
- DIOT Igloo2-based radiation-tolerant System Board · Add a reset button (for debugging)
- DIOT Igloo2-based radiation-tolerant System Board · Make FMC JTAG pull-{up,down} resistors unmounted by default
- DIOT Zynq Ultrascale-based System Board · power-supply-1: P1V8AUX_PG connected to wrong IC30 channel
- FMC-PROFINET · pull-down on RST_I FMC signal keeps ERTEC in reset unless FMC plugged on a carrier.
- FMC-PROFINET · Fix ERTEC reset circuit (Clock-Reset sheet)
- FMC-PROFINET · fix missing ERTEC JTAG connections
- DIOT Zynq Ultrascale-based System Board · SG-310 SCN is obsolete
- DIOT Zynq Ultrascale-based System Board · Add descriptions of sensors in schematics
- DIOT Zynq Ultrascale-based System Board · Wrong i2c address of MAX6639 on schematic
- DIOT Zynq Ultrascale-based System Board · DXP2 pin in MAX6639 not connected
- DIOT Zynq Ultrascale-based System Board · Update version resistors to reflect version v2.0
- DIOT Zynq Ultrascale-based System Board · Change license from CERN-OHL-S v2 to CERN-OHL-W v2
- DIOT Zynq Ultrascale-based System Board · Silkscreen modifications
- DIOT Zynq Ultrascale-based System Board · reorganise I2C bus
- DIOT Zynq Ultrascale-based System Board · add one more 24AA025E48-I/SN on I2C-WRFLASH bus
- DIOT Igloo2-based radiation-tolerant System Board · V1 - No link to project sources on the PCB silkscreen
- DIOT Zynq Ultrascale-based System Board · Improve routing of FMC transceivers
- DIOT Zynq Ultrascale-based System Board · add a fuse on 12V before it goes to the FMC
- DIOT Zynq Ultrascale-based System Board · TVS diodes are placed after the series resistors
- DIOT Zynq Ultrascale-based System Board · WR-clocks: R55, R56, R60, R242, R243 should not be mounted to generate 62.5MHz WR helper clock
- DIOT Zynq Ultrascale-based System Board · fpga-config: SDIO_PROTECT and SDIO_DETECT should be pulled-up to P3V3 and NOT P1V8
- DIOT Zynq Ultrascale-based System Board · fpga-config: PS_MODE1/2 swapped at FPGA pins
- DIOT Zynq Ultrascale-based System Board · fpga-config: R160, R161, R162, R163 should be not mounted to allow for boot mode selection with SW1
- DIOT Zynq Ultrascale-based System Board · Replace C100 with higher voltage rating
- DIOT Zynq Ultrascale-based System Board · The reset pin of the flash chips is connected to ps_por_b which is 3.3V while the flash are 1.8V
- DIOT Zynq Ultrascale-based System Board · Missing pull-ups for PWRBTN_N and PWR_FAIL_N